Windows 95/98, Windows NT4.0 | Ricoh AP505 specification

Troubleshooting

Note

•Windows 95/98

A Click [Start], point to [Settings], and then click [Printers].

B Select the icon of the printer by clicking it. Next, on the [File] menu, click

[Properties].

C Click [Details] tab.

D Check the [Print to the following port] box to make sure the correct port is selected.

•Windows NT4.0

A Click [Start], point to [Settings], and then click [Printers].

BSelect the icon of the printer by clicking it. Next, on the [File] menu, click

			[Properties].
	4
		C	Click [Port] tab.

DCheck the [Print to the following port] box to make sure the correct port is selected.

34

Image 52

Ricoh AP505 manual Windows 95/98, Windows NT4.0

Contents

Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During Operation Iii Page Specifications Low-power mode Energy Save modeEnergy Star Program Manuals for Your Printer Manuals for Your Printer How to Read this Manual Symbols Table of Contents Cleaning the Printer Moving and Transporting the Printer SpecificationsReplacing Consumables ConsumablesPage Guide to the Printer Exterior-Front View Bypass tray Paper Tray Exterior-Rear View Interior Operation Panel Turning the Printer On and Off Turning On the PrinterTurning Off the Printer Ready Installing Options Available Options Memory Unit Type505 ⇒ P.9 Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following items Initializing Press Enter to Initialize DiskPress Enter Installing the Paper Feed Unit Type305 Move the printer to make install- ing space Remove both pieces of adhesive tape Pull out the paper tray, and re- move the paddingRemove the ring attached to the red tag Place the printer on the paper feed unit Paper and Other Media Supported by this Printer Paper Types and Sizes Paper Sizes Metric version B6 JIS ⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paper Thick Paper Adhesive labels OHP transparencies Paper not supported by this printer Printable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up Printer Setup Specifying paper size using the operation panelSET * Size TRAY1 * Size Loading Paper in the Bypass Tray Open the bypass traySlide the side guides Load paper until it stops with the print side down Bypass Tray Size Sliding out the Output Tray ExtenderPress Enter until Bypass Tray Size appears Troubleshooting Error & Status Messages on the Operation Panel ⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt Print Terface cable If the printer is using the I/O timeout settingNetwork Connection Windows 95/98 Windows NT4.0 Other Printing Problems Status Possible Causes, Descriptions, and Solutions Tions for Paper Ing the Charger Removing Misfed Paper When the Message Open AppearsMisfeed Appears Bypass tray Tray Appears When the Message RemoveOpen the paper exit cover Remove the misfed paper from Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning the PrinterCleaning the Charger Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front cover TFWX280E Open the left cover Replacing ConsumablesSlide the lock lever up Remove the protective sheet from the new toner cartridge Hold the new toner cartridgeShake it with a horizontal motion About 10 times, as shown in the il- lustration Maintenance Magenta TonerMagenta Toner Please Wait Replace Toner Magenta Replacing the Photoconductor Unit Turn off the printers power switchReplace PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchFuser OIL LOW ADD Fuser OIL Remove the green cap from the new oil bottle Close the fuser oil bottle cover Insert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and Charger Locks release, and the charg- er is lifted slightly Appendix Moving and Transporting the Printer Specifications Mainframe Noise Emission Sound Power Level DimensionsWeight Warm-up Time Optional Equipment Options Consumables Toner Cartridge Service Life *1 Other Consumables Index