When the Message Remove, Tray Appears | Ricoh AP505 specs

Troubleshooting

AOpen the front cover by pushing the front cover release button.

TFWX080E	D

TFWX220E

Close the front cover.

		B If the paper is in the front side of
	4	B If the paper is in the front side of
	4	the photoconductor unit, careful-

ly pull it out.

Note

❒When removing misfed paper, be careful not to touch the fus- ing section because it could be very hot.

TFWX210E

CWhen the misfed paper is in the main section of the photoconduc- tor unit, turn the dial downward then remove the misfed paper in the printer.

Make sure that you do not leave any misfed paper in the printer.

Note

❒If it is difficult to turn the dial, turn it slightly upward in the opposite direction, and then try again.

When the Message "REMOVE

MISFEED FROM OUTPUT

TRAY" Appears

RCAUTION:

•When removing misfed paper, do not touch the fusing section because it could be very hot.

AOpen the paper exit cover.

Note

❒When opening the paper exit cover, be careful as it may be hot.

TFWX230E

40

Image 58

Ricoh AP505 manual When the Message Remove, Tray Appears, Open the paper exit cover

Contents

Printer Reference Overseas Affiliates Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Page Means Power ON. b means Power OFF Trademarks Safety Information Safety During Operation Iii Page Specifications Low-power mode Energy Save modeEnergy Star Program Manuals for Your Printer Manuals for Your Printer How to Read this Manual Symbols Table of Contents Replacing Consumables Cleaning the PrinterMoving and Transporting the Printer Specifications ConsumablesPage Guide to the Printer Exterior-Front View Bypass tray Paper Tray Exterior-Rear View Interior Operation Panel Turning Off the Printer Turning the Printer On and OffTurning On the Printer Ready Installing Options Available Options Memory Unit Type505 ⇒ P.9 Installing the Memory Unit Type505 Dimm For more information on Installing the Printer Hard Disk Type505 Check the contents of the box for the following items Initializing Press Enter to Initialize DiskPress Enter Installing the Paper Feed Unit Type305 Move the printer to make install- ing space Remove the ring attached to the red tag Remove both pieces of adhesive tapePull out the paper tray, and re- move the padding Place the printer on the paper feed unit Paper and Other Media Supported by this Printer Paper Types and Sizes Paper Sizes Metric version B6 JIS ⇒ P.27 Loading Paper in the Bypass Tray Paper Sizes Inch version ⇒ P.27 Loading Paper in the Bypass Tray Precautions for Paper Paper types and cautions Plain paper Thick Paper Adhesive labels OHP transparencies Paper not supported by this printer Printable Area Loading Paper in the Paper Tray Loading PaperLoad paper into the tray with the print side up SET * Size Printer SetupSpecifying paper size using the operation panel TRAY1 * Size Slide the side guides Loading Paper in the Bypass TrayOpen the bypass tray Load paper until it stops with the print side down Bypass Tray Size Sliding out the Output Tray ExtenderPress Enter until Bypass Tray Size appears Troubleshooting Error & Status Messages on the Operation Panel ⇒ P.38 Removing Misfed Pa Tle. ⇒ P.53 Replacing Waste Toner Bottle and Charg Possible Cause Solutions Printer Doesnt Print Terface cable If the printer is using the I/O timeout settingNetwork Connection Windows 95/98 Windows NT4.0 Other Printing Problems Status Possible Causes, Descriptions, and Solutions Tions for Paper Ing the Charger Removing Misfed Paper Misfeed Appears When the Message OpenAppears Bypass tray Tray Appears When the Message RemoveOpen the paper exit cover Remove the misfed paper from Remove the misfed paper from inside of the printerClose the paper exit cover Close the front cover Cleaning the Friction Pad Cleaning the PrinterCleaning the Charger Cleaning the Dust-proofing glass Remove the cleaning brush from back of the front cover TFWX280E Open the left cover Replacing ConsumablesSlide the lock lever up Shake it with a horizontal motion Remove the protective sheet from the new toner cartridgeHold the new toner cartridge About 10 times, as shown in the il- lustration Magenta Toner Please Wait MaintenanceMagenta Toner Replace Toner Magenta Replacing the Photoconductor Unit Turn off the printers power switchReplace PCU TFWX400E Replacing the Fuser Oil Bottle and Ozone Filter Turn on the printer’s power switchFuser OIL LOW ADD Fuser OIL Remove the green cap from the new oil bottle Close the fuser oil bottle cover Insert a new ozone filter into the printer Waste Toner Almost Full Replacing the Waste Toner Bottle and Charger Locks release, and the charg- er is lifted slightly Appendix Moving and Transporting the Printer Specifications Mainframe Weight Noise Emission Sound Power LevelDimensions Warm-up Time Optional Equipment Options Consumables Toner Cartridge Service Life *1 Other Consumables Index