Guidance Display Meaning | Ricoh JP1250, JP1210 specs

SilverV-gb.book Page 83 Monday, May 15, 2000 3:32 PM

If Your Machine does not Operate as You Want

❖When one of the following messages is displayed on the guidance display

Guidance Display	Meaning

RE-ENTER COPY NUMBER MAXIMUM	The maximum number of prints that can be
IS XXX	entered is specified by the Service Program
	mode. Change the number of prints.

RE-ENTER COPY NUMBER MINIMUM	The minimum number of prints that can be en-
IS XXX	tered is specified by the Service Program
	mode. Change the number of prints.

SET THE ORIGINALS	Make prints after you confirm whether there is
	an original.

INPUT YOUR ID CODE	User Code mode is set. Before printing, enter
	your user code.

NO ADDITIONAL PRINTS ALLOWED	Security mode is set. If you make the next mas-
	ter, Security mode is canceled.

MASTER MAKING HALTED	Master making is halted.
	Press the {Start} key.

-When a service code (E-XX) is displayed in the guidance display

Turn the main switch off and on. If a service code appears again, contact your service representative.

Note

❒If a service code appears on the guidance display after you turn the main switch off and on a few times, do not continue turning it on and off. Leave the machine off.

❒E04 might be displayed when you make masters continuously using the orig- inals that have solid images. In the case, turn off the main switch and wait for a while.

5

83

Image 103

Ricoh JP1250, JP1210 operating instructions Guidance Display Meaning

Contents

Operating Instructions JP1210/1250 Overseas Affiliates Introduction Means Power ON. b means Power OFF Safety During Operation Safety Information SilverV-gb.book Page ii Monday, May 15, 2000 332 PM Symbols How to Read this ManualIii What You Can Do with this Machine Printing on Thick or Thin Paper Erasing Centre and Edge MarginsErasing Edge Margins Erasing the Shadow of Pasted Originals Skip Feed Printing Storing Your Print Settings in MemoryGroup Printing from Different Originals Combining Originals onto One Print Vii Machine Exterior Viii Machine Interior Originals document feeder Options Keys Operation Panel Clear Modes/Energy Saver key Fine keyImage Position key Program key Xii Indicators Table of Contents Xiv 107 100101 102 Xvi Printing Paper Operation Originals Place the paper on the paper feed tray Preparation for PrintingLoading Paper Carefully open the paper feed tray Turn on the main switch Setting Up the Paper Delivery TrayOpen the paper delivery tray Printing Standard PrintingLower the platen cover Press the Start key SilverV-gb.book Page 6 Monday, May 15, 2000 332 PM Restoring Paper Feed and Paper Delivery Trays Energy Saver Mode Saving Energy Shifting the Print Image Position Forward or Backward Adjusting the Print Image PositionShifting the Image Position Forward or Backward Shifting the Image Position to the Right or Left Shifting the image to the right Shifting the Print Image Position to the Right or LeftShifting the image to the left After Making a Master Adjusting the Print Image DensityBefore Making a Master Before Making a Master Tint Mode-Halftone Printing Fine Mode-Making Clear Prints Changing the Printing Speed Press the Clear/Stop key Stopping the Machine during the Multi- print RunChange the number of prints or check the completed prints Reduction Inch version Reduction Metric version Enlargement Inch version Enlargement Metric versionMake your prints Press the or key to se- lect the paper size and direction Check Indicator is blinkingCentre/Edge Erase-Erasing centre and Edge Margins Center/Edge Erase key again Set the book on the exposure glass Edge Erase-Erasing Edge Margins Press the Center/Edge Erase key to select Edge Erase modeCenter/Edge Erase key twice Edge Erase-Erasing Edge Margins Set the original on the exposure glass Paste Shadow Erase-Erasing the Shadow of Pasted OriginalsPress the Paste Shadow Erase key Pressure Lever Position Printing on Thick or Thin Paper Selecting Original Type Photo modeLetter mode Letter/Photo mode Economy Mode-Saving Ink Enter the number of prints re- quired with the number keys Auto Cycle-Printing from Several Originals at OncePress the Auto Cycle key If you use the optional tape dis Power switchPenser, turn on the tape dispenser With the number keys, enter the desired number of sets Press the Memory/Class key to light the Class indicatorClass Mode-Group Printing from the Same Original Press the q key Turn on the optional tape dis- penser power switch Memory Mode-Group Printing from Different Originals Set the first original face down on the exposure glass Press the q key again Repeat this step until you have finished printing Press the Auto Cycle key Press the Print key Metric version Combine-Combining 2 Originals onto One PrintInch version Set the first original face down Reproduction Ratio To Choose a CustomPress the Center/Edge Erase Enter the number of prints with the number keys Skip Feed Printing Storing Your Settings Program-Storing Your Print Settings in Memory Recalling a Program Press the Start key Press the q key Protecting a ProgramPress the q key Enter 1 with the number keys Select the program number you Removing Program ProtectionWant to remove protection from Security Mode-Printing Secret Documents Document Feeder Exterior Printing Using the Optional 30 Originals Document Feeder Originals Adjust the guide to the original size Setting Originals in the Document Feeder Combine Copies with the Document Feeder Set the desired settings and press the Start keyCheck the print paper size and the reproduction ratio Press the Combine key to select your desired mode Memory Mode with the Document Feeder Set your originals face up into the document feeder Livered Turn on the optional tape dispenser power switch SilverV-gb.book Page 51 Monday, May 15, 2000 332 PM Open the front door Colour Printing Using the Optional Colour DrumMaking Colour Prints Changing the colour Drum Unit Lower the drum unit lock lever Pull out the drum unit handleInsert the colour drum unit along the guide rail Slide in the drum unit until it locks in position Printing in Two colours Set the second original and press the Start key Exchange the drum unit. See ⇒Check the image position Press the Print key SilverV-gb.book Page 56 Monday, May 15, 2000 332 PM Press the Clear Modes/Energy Saver key Reference Accessing Service ProgramsPress the Clear Modes/Energy Sav Er key Hold down the Clear/Stop key for at least 3 seconds After entering the desired SP No., press the q key Changing the Settings of Service ProgramsEnter the desired value or mode with the number keys Press the q key to store the desired value or mode Press the Clear Modes/Energy Saver key Service Program Menu SilverV-gb.book Page 60 Monday, May 15, 2000 332 PM Combine-Combining 2 Originals onto One Print SilverV-gb.book Page 62 Monday, May 15, 2000 332 PM Memory Mode-Group Printing from Different Default 3 Min. minutes SilverV-gb.book Page 65 Monday, May 15, 2000 332 PM Enter 1 Yes with the number keys and then press the q key How to Set User Code Mode #User Codes Er key Enter 120 with the number keys and press the q key Down the Clear Modes/Energy Sav How to Use User Code ModeEr key Press the Clear Modes/Energy Sav- er key How to Check the User Code Counter # Er key Enter 122 with the number keys and press the q key How to Clear the User Code Counter #Enter 1 Yes with the number keys and press the q key Enter 123 with the number keys and press the q key Enter 124 with the number keys and press the q key How to Clear the User Code Total Counter # SilverV-gb.book Page 72 Monday, May 15, 2000 332 PM Load paper on the paper feed tray Loading Paper on the Paper Feed TrayReplenishing Paper Press the Paper Feed Tray Down Changing the Paper Size Adjust the side plates and the end platePlace the paper on the paper feed Pull out the ink holder and remove the used ink cartridge When the Add Ink Indicator j Lights Insert the new cartridge into the ink holder Remove the cap of the new ink cartridge Open the original tray Master Roll ReplacementOpen the right side cover Open the plotter cover Close the plotter cover Set the paper edge of the master roll as shown As shown, put the roll in the dis- penser Turn on the power switch of the tape dispenserPlacing a New Roll of Tape in the Tape Dispenser Option Open the cover of the tape dis- penser SilverV-gb.book Page 80 Monday, May 15, 2000 332 PM If Your Machine does not Operate as You Want When the misfeed indicator x lights When other indicators light When the open cover/unit indicator M lights Guidance Display Meaning Press the ADF unit open lever and open the ADF unit Clearing Misfeeds+ Original JAM. Remove Original After clearing misfeeds Close the ADF unit until it locks in position Pull out the original gently To prevent original misfeeds Remove the misfed paper +PAPER Feed JAM. Remove Jammed PaperSlowly but firmly pull out the paper Pull out the drum unit To prevent paper misfeeds SilverV-gb.book Page 89 Monday, May 15, 2000 332 PM + Master Feed JAM. Remove Jammed Master Return the original tray to its original position +PAPER Wrap JAM. Remove Jammed Paper SilverV-gb.book Page 93 Monday, May 15, 2000 332 PM Pull out the master eject box +MASTER Eject JAM. Remove Jammed Master Return the master eject box to its original position Remove the misfed master Pull the master out of the master clamp +DELIVERY JAM. Remove Jammed Paper ADF Unit Option When the Open Cover/Unit Indicator M LightsOriginal Tray Front Door SilverV-gb.book Page 98 Monday, May 15, 2000 332 PM Take out the master eject box and remove the used masters When the Master Eject Indicator k Lights 100 When Other Indicators Light 101 When the Prints are Thrown Over the Paper Delivery TrayReduce the printing speed by pressing the W key Dirt on the Back Side of Paper Poor Printing102 103 Clean the pressure roller with a clean cloth 104 Dirt on the Front Side of Paper Black Line/Stain 105 White Prints or Incomplete Prints Remove the master from the drum 106Remove paper that is stuck to the drum General Cautions Operation Notes107 108 109 Print Paper 110 Environments to avoid Where to Put Your MachineEnvironmental Conditions Optimum environmental conditions 112 Power ConnectionAccess to Machine Main Frame Platen Cover Maintaining Your MachineMain Frame Exposure Glass Separation Roller Optional Document Feeder114 115 Combination Chart 116 Main Frame Print Speed Print Paper WeightPrinting Paper Size Leading Edge Margin Noise Emission *1 Dimensions W × D × HWeight Power Source Optional Equipment Power Consumption120 121 Original WeightOriginals Document Feeder Original Capacity 122 Consumables 123 Index Reduce key 124