Roberts Gorden DAT115 Roberts-Gordon,LLC, Table Of Contents, Heater Safety, User Instructions

TABLE OF CONTENTS

SECTION 1: Heater Safety		2	SECTION 12: User Instructions		25
SECTION 2: Installer Responsibility		2	12.1	User Instructions	25
2.1	Clearances to Combustibles	2	12.2	Heater Operation	25
2.2	Corrosive Chemicals	2	12.3	Common User Controls	25
2.3	National Standards and Applicable Codes	2	12.4	Cooling Section Operation	26
SECTION 3: Critical Considerations		3	12.5	Heating Section Lighting Instructions	26
3.1	Basic Information	3	12.6	Simple Fault Finding	26
3.2	Location and Suspension	3	SECTION 13: Servicing		28
3.3	Minimum Required Installation Clearances	3	13.1	Servicing Instructions	28
3.4	Clearances to Combustibles	3	13.2	Burner Maintenance	28
3.5	Ventilation	3	13.3	Fan/Motor Assembly Maintenance	28
3.6	Gas Supply	3	13.4	Heat Exchanger Maintenance	28
3.7	Electrical Supply	3	13.5	Gas Control Valve Maintenance	29
3.8	Flue	3	13.6	Flue Fan	29
3.9	Coil Condense Drain	3	SECTION 14: Conversion Between Gases		30
SECTION 4: Specifications		5	14.1	General	30
4.1	DAT	5	14.2	Burner Conversion	30
4.2	General Technical Data Table	6	14.3	Gas Valves	30
4.3	Technical Data Table - Heater Section	7	SECTION 15: Troubleshooting		31
4.4	DualAir® Performance Data - Graph of Air Flows v		15.1	General	31
	Static Pressure	8	15.2	Troubleshooting For Automatic Ignition Burner
SECTION 5: Heater Installation		9		Systems	32
5.1	General	9	15.3	Troubleshooting for Flame Supervision System	33
5.2	Handling	9	15.4	Troubleshooting for Solenoid Valves	34
5.3	Shelf Mounting and Suspension	9	15.5	Troubleshooting for Main Fan	34
SECTION 6: Flue Installation		10	15.6	Troubleshooting for Fan Contactor	35
6.1	Flue Installation	10	SECTION 16: Removal and Replacement Parts		36
6.2	Type C12, C32 & C62 Appliance	10	16.1	Gas Valve	36
6.3	Type B22 Appliance	10	16.2	Burner Compartment	37
6.4	Converting from Top to Side Terminations for Flue		16.3	Ignition Electrode and Flame Probe	38
	and Air Intake	10	16.4	Flue Fan	39
SECTION 7: Air Supply		13	16.5	Heater Pressure Switch	40
7.1 Room Sealed Installation		13	16.6	Cooling Coil Safety Devices	41
7.2 Open Flued Installation		13	16.7	Ignition Control	42
7.3 Building Ventilation		13	16.8	Fan Motor Removal	42
7.4 Isolated Equipment Rooms		13	16.9	Combination Fan/Limit Thermostat	43
SECTION 8: Optional Heater Configurations		14
8.1	Distribution Duct	14
SECTION 9: Gas Piping		15
9.1	Connections	15
SECTION 10: Wiring and Electrical Information		16
10.1 Electrical Supply		16
10.2 Remote Control		16
10.3 DAT Main Circuit Board Terminal Identification		17
10.4 DAT Wiring Diagram		18
10.5 DAT Wiring Diagram		19
10.6 DAT Site Connections at Main Circuit Board		20
SECTION 11: Commissioning		21
11.1 Pre-Commission Checks		21
11.2 Gas Supply		21
11.3 Mechanical Checks		21
11.4 Begin Commissioning		21
11.5 Combustion Testing		23
11.6 Turning Off the DualAir® Unit		24
11.7 External Controls		24
11.8 Complete the Commissioning		24
11.9 Instruction to the User		24

©2007 Roberts-Gordon, LLC

All rights reserved. No part of this work covered by the copyrights herein may be reproduced or copied in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping or information storage and retrieval systems - without the written permission of Roberts-Gordon, LLC.

Printed in U.K.