BLACKHEAT® HE INSTALLATION OPERATION AND SERVICE MANUAL
SECTION 1: HEATER SAFETY
Your Safety is Important to Us!
This symbol is used throughout the manual to notify you of possible fire, electrical or burn hazards. Please pay special attention when reading and following the warnings in these sections.
Installation, service and annual inspection of heater must be done by a registered installer/contractor qualified in the installation and service of
Read this manual carefully before installation, operation or service of this equipment.
This heater is designed for heating nonresidential indoor spaces. Do not install in residential spaces. These instructions, the layout drawing, local codes and ordinances, and applicable standards that apply to gas piping, electrical wiring, venting, etc. must be thoroughly understood before proceeding with the installation.
Protective gear is to be worn during installation, operation and service. Thin sheet metal parts, such as the reflector portion of the heater and the various venting components, have sharp edges. To prevent injury, the use of work gloves is recommended. The use of gloves will also prevent the transfer of body oils from the hands to the surface of the reflector.
Before installation, check that the local distribution conditions, nature of gas and pressure, and adjustment of the appliance are compatible.
The heater must be applied and operated under the general concepts of reasonable use.
For additional copies of the Installation, Operation and Service Manual, please contact
1.1 Manpower Requirements
To prevent personal injury and damage to the heater, two persons will be required for installation.
1.2 IP55 Protection
The burner is certified to protection class of IP55. This means that the internal components of the burner are protected against extreme dusty atmosphere and water jets from all sides. Outside air supply and flue are mandatory for this heater. The standard exhaust fans mentioned in this manual do NOT have IP55 protection and must be outside the wet environment. If the fan is to be installed in the wet environment, a special IP54 protected fan must be used. Consult
In order to have trouble free performance of your heater and maintain the IP55 protection, follow all instructions in this manual, especially the replacement of sealing gaskets.
1.3 Safety Labels and Their Placement
Product safety signs or labels should be replaced by the product user when they are no longer legible. Please contact
Figure 1: Bottom and Back Panel Label Placement
|
|
| Infrared Radiant Tube Heater |
|
|
| |
|
|
| This applicance must be installed in accordance with the |
|
|
| |
|
|
| rules in force, and used only in a sufficiently ventilated space. |
|
|
| |
|
| Consult instructions before installation and use of this applicance. |
|
|
| ||
| Model No. | Gas Type |
|
|
|
| |
| Serial No. |
|
|
|
|
| |
| Appliance Type | Category |
|
| Infrared Radiant Tube Heater | ||
| Gas Pressure |
|
| Model No. | Gas Type |
| |
| Orifice Size |
|
|
|
| ||
| at Manifold |
| Serial No. |
|
| ||
|
|
|
|
|
| ||
| Normal Input Rating | Electrical |
| Appliance Type | Category |
| |
|
| at Manifold | Orifice Size |
| |||
|
|
|
| V | Gas Pressure |
|
|
| (Net Calorific Value) | Rating |
| Electrical |
| ||
|
| Normal Input Rating | V | ||||
|
|
|
|
| (Net Calorific Value) | Rating | |
| Min. Input Rating |
|
| Min. Input Rating |
| Hz | |
| (Net Calorific Value) |
| Hz | (Net Calorific Value) |
| ||
|
| Destination |
| W | |||
| Fan/Burner Label |
|
| Country of |
|
| |
| Destination |
|
| Year of |
|
| |
|
| Country of |
| W | 0063 Production |
|
|
|
|
|
|
|
|
| |
|
| Year of |
|
|
|
|
|
| 0063 | Production |
|
|
|
|
|
| Rating Plate Label | Back Panel | |||||
Bottom Panel | Logo Label |
|
|
|
|
| |
Description | Part Number |
Logo Label | 91033200 |
|
|
Rating Plate Label | 91031300 |
|
|
Fan/Burner Label | 91033300 |
|
|
2 of 73
