Roland JUNO-D owner manual TM Ctrl DLY Time Control Delay, 23 2V PCH Shift 2-Voice Pitch Shifter

Parameter	Value	Description
HF Damp	200–8000 [Hz],	Adjusts the frequency above
	BYPASS	which sound fed back to the ef-
		fect will be cut.
		If you do not want to cut the
		high frequencies of the feed-
		back, set this parameter to BY-
		PASS.
Balance #	D100:0W–	Adjusts the volume balance be-
	D0:100W	tween the direct sound and the
		delay sound.
		With a setting of D100:0W only the
		direct sound will be output, and
		with a setting of D0:100W only the
		delay sound will be output.
Level	0–127	Adjusts the output level.

22: TM CTRL DLY (Time Control Delay)

Adding effects

Parameter	Value	Description
Balance	D100:0W–	Adjusts the volume balance be-
	D0:100W	tween the direct sound and the
		delay sound.
		With a setting of D100:0W only the
		direct sound will be output, and
		with a setting of D0:100W only the
		delay sound will be output.
Level	0–127	Adjusts the output level.

23:2V PCH SHIFT (2-Voice Pitch Shifter)

A Pitch Shifter shifts the pitch of the direct sound. This 2-voice pitch shifter has two pitch shifters, and can add two pitch shifted sounds to the direct sound.

fig.MFX-23

Balance D

You can change the delay time in real time. Lengthening the delay

will lower the pitch, and shortening it will raise the pitch.

fig.MFX-22

L in	2-Band	L out
	EQ
Balance D
	Balance W
Time Control Delay
	Balance W

L in

Level Balance A

2Voice Pitch Shifter

Level Balance B

R in

	L out
PanA L	Balance W

PanA R

PanB L

PanB R Balance W

R out

R in	Feedback		2-Band	R out
	Balance D		EQ
Parameter	Value	Description
Delay #	0–840 [ms]	Adjusts the time delay from the
		direct sound until when each de-
		lay sound is heard.
Feedback #	-98– +98 [%]	Adjusts the proportion (%) of
		the delay sound that is fed back
		into the effect.
		Negative (-) settings will invert
		the phase.
Acceleration	0–15	This parameter adjusts the time
		over which the Delay Time will
		change from the current setting
		to a newly specified setting.
		The rate of change for the Delay
		Time directly affects the rate of
		pitch change.
HF Damp	200–8000 [Hz],	Adjusts the frequency above
	BYPASS	which sound fed back to the ef-
		fect will be cut.
		If you do not want to cut the
		high frequencies of the feed-
		back, set this parameter to BY-
		PASS.
Pan	L64–63R	Adjusts the stereo location of the
		delay sound.
		L64 is far left, 0 is center, and
		63R is far right.
Low Gain	-15– +15 [dB]	Adjusts the gain of the low fre-
		quency.
High Gain	-15– +15 [dB]	Adjusts the gain of the high fre-
		quency.

		Balance D
Parameter	Value	Description
Mode	1, 2, 3, 4, 5	Higher settings of this parame-
		ter will result in slower re-
		sponse, but steadier pitch.
Coarse A #1	-24– +12 [semi]	Adjusts the pitch of Pitch Shift A
		in semitone steps (-2- +1 oc-
		taves).
Coarse B #2	-24– +12 [semi]	Adjusts the pitch of Pitch Shift B
		in semitone steps (-2- +1 oc-
		taves).
Fine A #1	-100– +100	Makes fine adjustments to the
	[cent]	pitch of Pitch Shift A in 2-cent
		steps (-100- +100 cents).
		One cent is 1/100th of a semi-
		tone.
Fine B #2	-100– +100	Makes fine adjustments to the
	[cent]	pitch of Pitch Shift B in 2-cent
		steps (-100- +100 cents).
		One cent is 1/100th of a semi-
		tone.
Pre Delay A	0–500 [ms]	Adjusts the time delay from
		when the direct sound begins
		until the Pitch Shift A sound is
		heard.
Pre Delay B	0–500 [ms]	Adjusts the time delay from
		when the direct sound begins
		until the Pitch Shift A sound is
		heard.
Pan A	L64–63R	Adjusts the stereo location of the
		Pitch Shift A sound.
		L64 is far left, 0 is center, and
		63R is far right.	Effects
Pan B	L64–63R	Adjusts the stereo location of the
		Pitch Shift B sound.
		L64 is far left, 0 is center, and
		63R is far right.

77