Roland JUNO-D owner manual FB PCH Shift Feedback Pitch Shifter, Reverb

Adding effects

Parameter	Value	Description
Level Balance	A100:0B–	Adjusts the volume balance be-
	A0:100B	tween the Pitch Shift A and Pitch
		Shift B sounds.
Balance	D100:0W–	Adjusts the volume balance be-
	D0:100W	tween the direct sound and the
		pitch shift sound.
		With a setting of D100:0W only the
		direct sound will be output, and
		with a setting of D0:100W only the
		pitch shift sound will be output.
Level	0–127	Adjusts the output level.

24:FB PCH SHIFT (Feedback Pitch Shifter)

This pitch shifter allows the pitch shifted sound to be fed back into

the effect.

fig.MFX-24

L in			2-Band	L out
	Balance D		EQ
			Balance W
	Pitch Shifter		Balance W
	Feedback
R in			2-Band	R out
	Balance D		EQ
Parameter	Value	Description
Mode	1, 2, 3, 4, 5	Higher settings of this parame-
		ter will result in slower re-
		sponse, but steadier pitch.
Coarse #1	-24– +12 [semi]	Adjusts the pitch of the pitch
		shifted sound in semitone steps
		(-2- +1 octaves).
Fine #1	-100– +100	Makes fine adjustments to the
	[cent]	pitch of the pitch shifted sound
		in 2-cent steps (-100- +100 cents).
Pre Delay	0–500 [ms]	Adjusts the time delay from
		when the direct sound begins
		until the pitch shifted sound is
		heard.
Feedback #	-98– +98 [%]	Adjusts the proportion (%) of
		the processed sound that is fed
		back into the effect.
		Negative (-) settings will invert
		the phase.
Pan	L64–63R	Adjusts the stereo location of the
		pitch shifted sound.
		L64 is far left, 0 is center, and
		63R is far right.
Low Gain	-15– +15 [dB]	Adjusts the gain of the low fre-
		quency.
High Gain	-15– +15 [dB]	Adjusts the gain of the high fre-
		quency.
Balance	D100:0W–	Adjusts the volume balance be-
	D0:100W	tween the direct sound and the
		pitch shift sound.
		With a setting of D100:0W only the
		direct sound will be output, and
		with a setting of D0:100W only the
		pitch shift sound will be output.
Level	0–127	Adjusts the output level.

25: REVERB

The Reverb effect adds reverberation to the sound, simulating an

acoustic space.

fig.MFX-25

L in				2-Band	L out
		Balance D		EQ
			Balance W
	Reverb		Balance W
R in				2-Band	R out
		Balance D		EQ
Parameter		Value		Description
Type		ROOM1,		Selects the type of Reverb effect.
		ROOM2,		ROOM1: dense reverb with
		STAGE1,		short decay
		STAGE2,		ROOM2: sparse reverb with
		HALL1,		short decay
		HALL2		STAGE1: reverb with greater
				late reverberation
				STAGE2: reverb with strong ear-
				ly reflections
				HALL1: reverb with clear rever-
				berance
				HALL2: reverb with rich rever-
				berance
Pre Delay		0.0–100 [ms]		Adjusts the time delay from
				when the direct sound begins
				until the reverb sound is heard.
Time #		0–127		Adjusts the time length of rever-
				beration.
HF Damp		200–8000 [Hz],		Adjusts the frequency above
		BYPASS		which the reverberant sound
				will be cut.
				As the frequency is set lower,
				more of the high frequencies
				will be cut, resulting in a softer
				and more muted reverberance.
				If you do not want the high fre-
				quencies to be cut, set this pa-
				rameter to BYPASS.
Low Gain		-15– +15 [dB]		Adjusts the gain of the low fre-
				quency.
High Gain		-15– +15 [dB]		Adjusts the gain of the high fre-
				quency.
Balance #		D100:0W–		Adjusts the volume balance be-
		D0:100W		tween the direct sound and the
				reverb sound.
				With a setting of D100:0W only the
				direct sound will be output, and
				with a setting of D0:100W only the
				reverb sound will be output.
Level		0–127		Adjusts the output level.

78