Roland JUNO-D owner manual Through, Stereo EQ Stereo Equalizer, Overdrive

Send Lvl to Cho

(Multi-effect send level to chorus)

Sets the amount of the multi-effects sound that is sent to the chorus. Higher values result in more sound being sent.

Value: 0–127

Send Lvl to Rev

(Multi-effect send level to reverb)

Sets the amount of the multi-effects sound that is sent to the reverb. Higher values result in more sound being sent.

Value: 0–127

Ctrl 1, 2 (Multi-Effects Control 1, 2)

On the JUNO-D, certain multi-effect parameters can be assigned to the modulation lever, knobs, pedal or D Beam. Of the parameters explained in Multi-effect parameters, the assignable parameters are marked with a “#” symbol. (Parameters marked with “#1” or “#2” can be simultaneously controlled using the controller marked with the same number.) Here you can exchange these assignments, or choose not to use them. For details, refer to p. 33, p. 89.

Value

OFF: Multi-effect control will not be used.

Items with a “#” symbol: The parameters that can be assigned to Ctrl1 or Ctrl2. These differ depending on the multi-effect type.

00: THROUGH

Effects are not applied. Select when creating Patches or Rhythm Sets that do not use multi-effects.

01: STEREO EQ (Stereo Equalizer)

This is a four-band stereo equalizer (low, mid x 2, high).

fig.MFX-01
L in			L out
	4-Band EQ
R in			R out
	4-Band EQ
Parameter	Value	Description
Low Freq	200, 400 [Hz]	Selects the frequency of the low
		range.
Low Gain	-15– +15 [dB]	Adjusts the gain of the low fre-
		quency.
High Freq	2000, 4000, 8000	Selects the frequency of the high
	[Hz]	range.
High Gain	-15– +15 [dB]	Adjusts the gain of the high fre-
		quency.
Mid1 Freq	200–8000 [Hz]	Adjusts the frequency of Middle
		1 (mid range).
Mid1 Q	0.5, 1.0, 2.0, 4.0,	This parameter adjusts the
	8.0	width of the area around the
		Middle 1 Frequency that will be
		affected by the Gain setting.
		Higher values of Q will result in
		a narrower area being affected.

Adding effects

Parameter	Value	Description
Mid1 Gain	-15– +15 [dB]	Adjusts the gain for the area
		specified by the Middle 1 Fre-
		quency and Q settings.
Mid2 Freq	200–8000 [Hz]	Adjusts the frequency of Middle
		2 (mid range).
Mid2 Q	0.5, 1.0, 2.0, 4.0,	This parameter adjusts the
	8.0	width of the area around the
		Middle 2 Frequency that will be
		affected by the Gain setting.
		Higher values of Q will result in
		a narrower area being affected.
Mid2 Gain	-15– +15 [dB]	Adjusts the gain for the area
		specified by the Middle 2 Fre-
		quency and Q settings.
Level #	0–127	Adjusts the output level.

02: OVERDRIVE

This effect creates a soft distortion similar to that produced by

vacuum tube amplifiers.

fig.MFX-02

L in						L out
						Pan L
	Over		Amp		2-Band
	drive		Simulator		EQ	Pan R
R in
						R out
Parameter		Value		Description
Drive #		0–127		Adjusts the degree of distortion.
				The volume will change togeth-
				er with the degree of distortion.
Pan #		L64–63R		Adjusts the stereo location of the
				output sound.
				L64 is far left, 0 is center, and
				63R is far right.
Amp Type		SMALL,		Selects the type of guitar amp.
		BUILT-IN,		SMALL: small amp
		2-STACK,		BUILT-IN: single-unit type amp
		3-STACK		2-STACK: single-unit type amp
				3-STACK: large triple stack amp
Low Gain		-15– +15 [dB]		Adjusts the gain of the low fre-
				quency.
High Gain		-15– +15 [dB]		Adjusts the gain of the high fre-
				quency.
Level		0–127		Adjusts the output level.

Effects

69