Roland JUNO-Gi LIVE SET EDIT Parameter

36
For details on how to edit in each screen, refer to “Basic Operations in
the LIVE SET EDIT Screen” (p. 34).
LIVE SET EDIT 1 Screen
[1] (TONE)
Parameter Value Explanation
Type
(Tone.Type).
Tone type of each layer
Tone These are instruments such as piano or strings. All
keys will play the sound of the same instrument.
Rhythm These are instruments such as drum sets. Each key
will play the sound of a dierent instrument.
Group
(Tone.Group).
Tone group of each layer
PRST These are the tones unique to the JUNO-Gi.
GM
These are tones compatible with the GM2
specication which was created as a common
standard for MIDI devices across manufacturers
and models.
Number
(Tone.Number). 001– Tone number of each layer
[2] (LV&PAN)
Parameter Value Explanation
Level 0–127 Volume of each layer. This setting’s main purpose
is to adjust the volume balance between layer.
Pan L64–0–63R Left/right position of each layer
Sw
(Layer.Switch).
OFF,
ON (✔) Layer on/o setting
Voice
(Voice.Reserve). 0–63, FULL
This setting species the number of voices that
will be reserved for each layer when more than
128 voices are played simultaneously.
* It.is.not.possible.for.the.settings.of.all.layers.
to.total.an.amount.greater.than.64..The.
remaining.number.of.available.voices.will.
be.displayed.at.(rest=)..Pay.attention.to.this.
readout.as.you.make.Voice.Reserve.settings.
* The.JUNO- Gi.is.able.to.play.up.to.128.notes.
simultaneously..The.polyphony,.or.the.
number.of.voices.(sounds).does.not.refer.
only.to.the.number.of.live.sets.actually.being.
played,.but.changes.according.to.the.number.
of.tones.used.in.the.live.sets,.and.the.number.
of.waves.used.in.the.tones.
[3] (PITCH)
Parameter Value Explanation
Octave
(Octave.Shift). -3–+3
Pitch of the layer’s sound (in 1-octave units)
* Note.that.when.a.rhythm.set.is.assigned.
to.a.layer,.you.cannot.modify.this.
parameter.
Coarse
(Coarse.Tune). -48–+48 Pitch of the layer’s sound
(in semitones, +/-4 octaves)
Fine
(Fine.Tune). -50–+50 Pitch of the layer’s sound
(in 1-cent steps; one cent is 1/100th of a semitone)
Bend
(Pitch.Bend.
Range).
0–24
Amount of pitch change in semitones (2 octaves)
that will occur when the Pitch Bend Lever is
moved. The amount of change when the lever
is tilted is set to the same value for both left and
right sides.
TONE The bend range setting specied by the tone will
be used.
[4] (OUTPUT)
Parameter Value Explanation
Asgn
(Output.Assign).
(Output.MFX.
Select).
Species for each layer how the direct sound will be output.
• Chorus and reverb are output in mono at all times.
• The output destination of the signal after passing through the
chorus is set with the “Chorus Output” (p. 45) parameter.
MFX
1–2
Output in stereo through multi-eects. You can
also apply chorus or reverb to the sound that
passes through multi-eects. Specify which
multi-eects (1–2) will be used.
L+R Output in stereo to the OUTPUT jacks without
passing through the multi-eect
LOutput in mono to the OUTPUT L jack without
passing through the multi-eect
ROutput in mono to the OUTPUT R jack without
passing through the multi-eect
Output
(Output.Level). 0–127 Level of the signal that is sent to the output
destination specied by Asgn
Chorus
(Chorus.Send.
Level).
0–127 Level of the signal sent to chorus for each layer
Reverb
(Reverb.Send.
Level).
0–127 Level of the signal sent to reverb for each layer
[5] (KEYBORD)
Key Range Lower Key Range Upper
Key Fade Lower Key Fade Upper
Level The layer sounded in the
lower range
The layer sounded in the
upper range
Pitch
Parameter Value Explanation
K.L
(Key.Range.
Lower).
C-–(Upper) Species the lowest note that the layer will sound
for each layer.
K.U
(Key.Range.
Upper).
(Lower)–
G9
Species the highest note that the layer will sound
for each layer.
F.L
(Key.Fade.
Lower).
0–127
Determines what will happen to the layer’s level
when a note that’s lower than Key Range Lower is
played. If you don’t want the layer to sound at all,
set this parameter to "0."
F.U
(Key.Fade.
Upper).
0–127
Determines what will happen to the layer’s level
when a note that’s higher than Key Range Upper is
played. If you don’t want the layer to sound at all,
set this parameter to "0."
LIVE SET EDIT Parameter