Applying Effects to the Sound | Roland VC-1 D-50 manual

Applying Effects to the Sound

The performance controlling functions (we call them factors in this manual) in each Patch can be edited by taking the following procedure.

A patch consists of several Factors as show below.

fig.05-01e(PatchFactorImage)

		Tone Tune
		UPPER Tone
	Key Mode	Variations of	Tone	Output Mode
	Key Mode	Control Functions	Balance	(Reverb, etc.)
		Control Functions	Balance	(Reverb, etc.)

LOWER Tone

Tone Tune

15

Image 15

Roland VC-1 D-50 owner manual Applying Effects to the Sound, 01ePatchFactorImage

Contents

03897845 ’05-3-1N Page Page Table of Contents Table of Contents Editing and Performances That Surpass the Original Main FeaturesIntroduction Perfect Simulation of the D-50’s Tones What is the digital synthesizer D-50? Panel Descriptions Front PanelNumber KEY Mode ShiftExit Rear Panel Try Out the Sounds Turning On the Power Selecting Patches and Playing Sounds Selecting Patches with the Value dial Selecting Patches from the ListSelecting Patches with Patch Palette Enabling or Disabling the Beep Tone Viewing Various Information 01ePatchFactorImage Applying Effects to the Sound Assigning Parameters to the Controllers Controllers ParametersKeys Functions List OSC1, OSC2, COSM1, COSM2 and TVA Specify the Tones or the Partials to be applied You can control the following parameters Settings Common to All Screens How to Make the Patch Factors SEP WholeDual Split Value AfterPB Aftertouch, Pitch Bender Hold Hold ModeMode Portamento Mode Bend Bender Range Output Output Mode Mode Output ModeValue Display Function Revbal Reverb Balance Vol Total VolumeRevType Reverb Type Value Display Description Value Time Chase Time Mode Chase ModeULL ULU Level Chase Level SepCH Receive Channel in Separate Mode LTune Fine Tuning of the Lower ToneUTune Fine Tuning of the Upper Tone TxBS Transmit Bank Select Switch Naming a Patch Saving Patches You’ve Created Saving Patches Reset to Default Factory Settings Touch Factory RESET. The Factory Reset screen appearsVC-1’s File Structure Transferring Patches from the D-50 to the VC-1 Transferring Patches To and From the D-50/550 Using the D-50 Using the D-550Transfer the patch from the memory card to the D-50/550 Transferring Patches from the D-50/550 to the VC-1 Destination Bank Saving Transferred PatchesTouch Data TRANSFER. The Data Transfer screen appears DEC Source Bank Transferring Patches from the VC-1 to the D-50/550 Touch SystemINC/+ or DEC Source Bank 3-1 Copying a Reverb Type Value 17 Value1 Destination Bank Temporary Area Overview of the VC-1Memory Structure Work Area Basic Concept of a Tone PartialSynthesizer sound generator PCM sound generator StructureTone Patch Ring Modulator WG Wave Generator Structure of Tone Parameters LFO Low Frequency TVF Time Variant FilterTVA Time Variant Amplifier ENV Envelope Generator Creating a Patch How to Make the Patch Settings Cursor Buttons Useful Functions for EditingEditing a Value Undoing an editing Operation Silencing the Sound of the Partial Editing with the Panel Controls Partial Select Copying Tone Settings CancelDisplay Value TVF Copying Parameter SettingsALL Common Auditioning the Sound Before Editing When Is set to All or Common Setting is ignored Patch Factor Initializing Patch SettingsCtrl Setup Check All EQ/CHORUS Tone ParametersCommon Parameters Structure Velo Velocity Range ENV Pitch EnvelopeENV Edit Envelope ENV Time Edit ENV Level Edit Pitch Mod Pitch Modulation LFO Low Frequency Oscillator KEY EQ/CHORUS Equalizer/ChorusEQ Edit Equalizer OFF Chorus Edit Pitch Partial Parameters Wave Waveform WG Form WG WaveformWG Form Waveform WG PW WG Pulse Width Display LFO Phase Value -7-+7 After Aftertouch RangeValue -7-+7 LFO LFO Select KF Keyfollow pitch WG PitchCoars Pitch Coarse Value C1-C7 Fine Pitch Fine WG Mod WG Modulation LFO LFO ModeENV P-ENV Mode Bend Bender Mode Bender Mode Example TVF Time Variant FilterFreq Cutoff Frequency Display Example Example Function Reso ResonanceKFKeyfollow Cutoff Point BP Bias Point TVF ENV TVF Envelope Value T5 Time TVF ENV Time TVF ENV Level Display Example Function Example Value Volume AdjustmentTVA Time Variant Amplifier Value -50-+50 BP Bias Point TVA ENV Envelope TVA ENV TimeVelo Velocity Follow Time TVA ENV Level Value -7-+7 MOD Modulation TVA MOD Settings for the Entire VC-1 How to Make the System Function SettingsDEC Digital Freq Digital Frequency Sound SettingMaster Tune Sound Character Value 1 SeparateCH Receive Channel in Separate ModeProg.C Program Change Switch Midi CH Midi Channel TxEDIT Exclusive Exclusive SwitchBank.S Bank Select Switch Dump Initializing the System Settings Mono Mode, Poly Mode Key Mode Alteration Split Key Mode Poly Mode Mono Mode Mode Message OffDual Dual-S Sound List Preset PatchesP1 Preset 1Original D-50 P2 Preset 2 New P4 Preset 4PN-D50-02 P3 Preset 3PN-D50-01 P5 Preset 5PN-D50-03 P6 Preset 6PN-D50-04BANK1 Patch Factors Value Comment Patch Factors Tone Parameters Common ParametersParameter Value Parameter Value Comment Partial Parameters TVF ENV Midich System Parameters Number Display PCM Name WaveformOneshot Loop Loop Some of the sounds 1 to 76, are combined and looped Newly Added WaveformsNumber Display Data Transmission Midi Implementation Receive data Mono Controller number Exclusive Communication Partial Parameter Common Parameter Patch Parameter Supplementary Material Midi Implementation Chart VC-1 V-Card D-50 Specifications Index Index 100