Samsung CLX-3175N, CLX-3175FW, CLX-3175FN Setting UP the Network, Supported operating environments

SETTING UP THE NETWORK

You need to set up the network protocols on the machine to use it in the network environment. You can set up the basic network settings through the machine's control panel.

Supported operating environments

The following table shows the network environments supported by the machine:

ITEM		REQUIREMENTS
Network interface	•	Ethernet 10/100 Base-TX
	• 802.11 b/g Wireless LAN
		(CLX-3175FW only)
Network operating system	•	Windows 2000/XP/2003/Vista
	•	Various Linux OS
	• MAC OS 10.3 ~ 10.5
Network protocols	•	TCP/IP
	•	Standard TCP/IP
	•	LPR
	•	IPP/HTTP
	•	Bonjour
	•	DHCP
	•	BOOTP

If you are in a non-static IP address environment and need to setup a DHCP network protocol, go to the http://developer.apple.com/ networking/bonjour/download/, select the program Bonjour for Windows due to your computer operating system, and install the program. This program will allow you to fix the network parameter automatically. Follow the instruction in the installation window. This

Bonjour program does not support Linux.

Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.

1.Make sure your machine is connected to the network with an RJ-45 Ethernet cable.

2.Make sure you have turned on the machine.

3.Press Menu on the control panel, until you see Network on the bottom line of the display and press OK.

4.Press the left/right arrow until TCP/IP appears and press OK.

5.Press the left/right arrow until Static appears and press OK.

6.Press the left/right arrow until IP Address appears and press OK. Enter a byte between 0 and 255 using the number keypad and press the left/right arrow to move between bytes.

Repeat this to complete the address from the 1st byte to the 4th byte.

7.When you have finished, press OK.

Repeat steps 6 and 7 to configure the other TCP/IP parameters: subnet mask and gateway address.

Contact the network administrator if you are not sure how to configure.

You can also set up the network settings through the network administration programs.

•SyncThru™ Web Admin Service: Web-based printer management solution for network administrators. SyncThru™ Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network machines from any site with corporate

internet access. Download this program from http:// solution.samsungprinter.com.

•SyncThru™ Web Service: Web server embedded on your network print server, which allows you to:

-Configure the network parameters necessary for the machine to connect to various network environments.

-Customize machine settings.

•SetIP: Utility program allowing you to select a network interface and manually configure the IP addresses for use with the TCP/IP protocol. (See "Using the SetIP program" on page 27.)

Using the SetIP program

This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it helps the network administrator set several network IPs at the

same time.

• You can only use SetIP program when your machine is connected to a network.

•The following procedure is based on windows XP. If you use Macintosh or Linux OS, see Software section

Installing the program

1.Insert the driver CD provided along with your machine. When the driver CD runs automatically, close the window.

2.Start Windows Explorer and open the X drive. (X represents your CD- ROM drive.)

3.Double-clickApplication > SetIP.

4.Double-click Setup.exe to install this program.

5.Click OK.

If necessary, select a language from the drop-down list.

6.Follow the instructions in the window and complete the installation.

Setting network values

1.Print the machine’s network configuration report to find your machine’s MAC address. See "Printing reports" on page 61.

2.From the Windows Start menu, select All Programs > Samsung Network Printer Utilities > SetIP > SetIP.

3.Click to open the TCP/IP configuration window.

4.Enter the network card's MAC address, IP address, subnet mask, default gateway, and then click Apply.

when you enter the MAC address, enter it without colon(:).

5.Click OK, then the machine prints the network information. Confirm the settings are correct.

6.Click Exit.

Getting started_ 27