Partition in the Freezer | Samsung RM255BABB, RM255BASB specs

DISASSEMBLY AND REASSEMBLY

PARTITION IN THE FREEZER

The Partition is located in the lower part of the freezer.Before separating the partition,take out all the shelves and cases which are above the partition.

1. Unscrew the partition(a screws).

2.Insert the flat-tip screwdriver into the center groove of the partition, and lift it up.

3.Insert the flat-tip screwdriver in the center of insulation-partition, and lift it up slightly. And then open the door in the power compartment, and lift it upward to separate.

EVAPORATOR COVER

For the disassembly of evaporator cover, water tank and partition should be disassembled first..

1.Remove the cap screws(2 pieces), and then remove other screws(4 pieces).

screws

2. Pull the upper part of the evaporator cover slightly.

3.Separate the housing terminal connected to the right side of evaporator cover, and lift it up carefully using both hands.

52

Image 53

Samsung RM255BABB, RM255BASB manual Partition in the Freezer, Screws Pull the upper part of the evaporator cover slightly

Contents

RM255BARB RM255BASB RM255BABB Authorized Training Center Campuses Important Safety Notice Contents Precautionssafety Warnings Symbols Forbidden Product Specifications Manual This operation instruction covers various models After packing 386lbs Model SpecificationRM25 Sensor Electric Parts Specification Electric Components Specifications Model Dispenser Home BarItems Running Part Code Optional Material SpecificationsPhotograph Operating Instructions & Installation Digital Panel Temperature Control Operation Power Freeze Operation Power Freeze and Power cool OperationPower cool Operation By in inside function irrespective of current setting Lock Function At Initial Power OnAble to operate on front panel Cube / Crushed / ICE OFF Selection Function Water Dispenser Function Machine Room F-Fan Motor Delay FunctionLight Operation Load Operation Condition Reverse rotation CCW Forward rotation CW Ice extraction Initial OperationHorizontal position Interval about 880ms Maximum torsion point Ice-Making Function Water Supply FunctionIce Extraction Function Water Supply Time Bold numerals indicate relevant ice tray steps Horizontality operation Defrosting period is fixed to 8 hours Defrosting FunctionArctic Zone 53.6 62.6 Function Arctic Select Zone FunctionOperation Fresh Select Zone Function Temp .8 ~ 44.6 of the Fridge compartment Function Operation SpecificationTest KEY Operation start For the R compartment Forced Defrosting Function Communication Error Display Function Alarm FunctionWhen water supply is finished, in the ice maker test mode Display Function at Panel Self-Diagnostics Function Operating Instructions & Installation BAD Item Trouble Status Self-Diagnostics Checklist Defrosting ErrorSensor of R CR Sensor CR-FAN Error CF-FAN ErrorOn Error Trouble Relevant displays about load status is as follows Load Mode Checklist Load Item Load StatusLoad Condition Display Function Option Setting Function Changing to Optional Mode Value Item KEY Function Change for freezer compartment Temperature Change Table for the Freezer Compartment KEY Temperature Change Table for the Refrigerator Compartment Case of basic model, the following items cannot be set CR Room Temperature Shift FunctionMaker For Ice Maker Flow sensor Disassembly and Reassembly Door Assy Removing the Front Leg Cover Removing the Freezer Door Removing the Refrigerator Door Liner on the right side of the rail To separate it Open the Fresh Select Zone DoorRemove two screws holding it to Reattaching the Freezer Door Reattaching the Refrigerator Door Levelling Zone Open the Arctic Select Zone Door Close the filter cartridge cover Do not overtighten the compression Note nutWater line must be connected to drinkable water only Control Panel Door Sub PartsDoor Handle Door Gasket Refrigerator Light Refrigerator Door Light SwitchTempered Glass Shelf Plastic Drawers in the Refrigerator Freezer Compartments Freezer Door Light SwitchDoor Bin in Freezer Plastic Drawer in Freezer Freezer Light Ice Dispenser Ice MakerTighten the screws 2 of the ice maker support Upper Ductwork Auger Motor Case Screws Pull the upper part of the evaporator cover slightly Partition in the Freezer Evaporator in Freezer Evaporator Fan Motor Thermistor cover Screw Freezer ThermistorIce-Maker Thermistor Water Tank Evaporator Fan Motor in Refrigerator Evaporator cover in the Refrigerator Refrigerator Thermistor Evaporator in FridgeDuctwork Thermistor Thermistor cover Fresh /Arctic Select ZoneTM Thermistor Upper Ductwork PCB-MAIN Assy Machine Compartment Electric BoxSub-condenser Water Solenoids Removing the Arctic Select Zone Accessories Start If power is not onNormal Check at the Smps PBA Check Main PCB connection If the compressor doesn’t work normally Check connector for Contact failureExchange and repair COMP. Assembly Perform forced defrosting for F R room one at a time Reference How To Check Temperature Sensing in the manual If the ambient temperature sensor has troubleIf there is a trouble with self-diagnosissensor failure Check the soldering on the main PCB for Shorts & breaks If Ding-Dong sounds continuously Start Alarm Sounds continuouslyrelated to the buzzerIf Beep sounds continuously Start Gasket, food etc Main PCB is normal, buzzer is Normal If the buzzer doesn’t soundBuzzer is broken - replace it Replace buzzer or panel PCB It is a care Where the Panel PCB key isn’t selectedIf the panel PCB is not working normally Door S/W If fan motor doesn’t working normalyDoor Open 0V DC Condition Door Open DC These signals will be inputted into Micom If Ice Cubed or/and Ice Crushed dont work normally Replace Inside lamp Replace or troubleshoot Door S/W If Indoor Lamp of Freezer/Refrigerator doesn’t light If Water Drawer doesnt work normally Preliminary Check Replace connector and wire Replace connector Wire and switchIf Dispenser LED Lamp doesnt light Failure of panel PCB itself Wiring Diagram Connector Arrangement Main Board Circuitschematic Diagram Conn Ector Arrangement SMP S Board A voltage proportional to Power BUS 93.7 40.0 88.9 38.2 84.2 36.4 79.8 34.6 75.7 32.8 71.8 98.968.2 64.7 107 IC75 Input IC75 Output FAN#18 GND0.8V Principle of Operation Motor Drive Circuit DescriptionsComparison in HIGH/LOW Speed Remarks XAA Reference Information 13-2 Q & a Problem Possible Causes What To Do Small or hollow cubes Problem Possible Causes What To Do Suction Pipe Additional InformationCompressor Sub-condenser Hot Pipe Dryer Step valve Freezer Refrigerator