Housing Elements | Schneider Electric XPSMF2DO801 instruction

Equipment Description

Housing Elements

Front View	The following image shows the various elements of the front panel of
	XPSMF2DO801 safety remote output module:
	1	2	2	2	2

L- L- L+ L+	1 2	3 4	5 6	7 8
L- L- L+ L+	DO1	DO2	DO3	DO4

	24V DC
	RUN	HIMatrix F28 01
	FAULT	HIMatrix F28 01
	ERROR	by HIMA
	PROG	DO
	FORCE	DO
	FORCE
	OSL
	BL

DO5	DO6	DO7	DO8
HIMA

1	10/100BaseT	10/100BaseT	2	9	10	11	12	13	14	15	16
1	10/100BaseT	10/100BaseT	2

3

2

2

2

Elements of the front panel:

No.

1

2

3

Description

Power supply input

Relay outputs

Indicators

36	33003405 07/2007

Image 36

Schneider Electric manual Housing Elements, XPSMF2DO801 safety remote output module, Elements of the front panel

Contents

XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a Glance Safety Information ProcedureImportant Information Safety Information About the Book At a Glance 33003405 07/2007 Overview XPSMF2DO801 Overview Whats in this Chapter?Topic Introduction RepresentationFront View Module Dimensions Dimensions Remote output module Side View Installation ProcedureIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Installation with spacers Length of the required spacer is calculated as follows= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Housing InternalConvection Variable Description Temperature State/Operating Temperature range Temperature state Overview Application and Function XPSMF2DO801 safety remote output module Initial OperationOverview Stage Application Function Terminal No Designation Function relay output Application and Function Cable DisconnectionFollowing will occur System Power Supply Interruption Large System ReconfigurationVoltage level Reaction of the controller Step Short-Circuit Characteristics Output Channels SHORT-CIRCUIT Condition Modules Offline Proof Test Periodic Proof Testing Offline Proof-TestExecution Offline Proof Equipment Description Output moduleWhats in this Chapter? Housing Elements XPSMF2DO801 safety remote output moduleElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Reset Button Using ResetHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Overview Safety-Related Communication Communication via switchesCommunication HIMatrix F3AIO Following scheme shows a SafeEthernet networking example Following is a Ethernet cable connection diagram Connector pairs and cable distancesNumber Maximum cable distance Equipment Description LEDs LED Description Following table describes behaviors of the LEDsColor Status Meaning LED Wiring Ethernet WiringInterface Elements RJ45 Connector SwitchesClass D capacity are required Recommended IP Addressing and System ID DescriptionBit numbers e.g SafeEthernet 33003405 07/2007 Operation ParametersEthernet Interfaces Connections for SafeEthernet/ Networking Examples Used Network Ports for Ethernet CommunicationUDP ports and usage TCP ports and usage OSI model For the next higher level and relies on the next lower level Following table describes the seven OSI layers bottom-top Number Layer Data Description Operating Conditions ClimaticConditions Mechanical EMC ConditionsFollowing tables Equipment Description Technical Characteristics Mechanical Data Power Supply ConnectorsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Relay Outputs Supply voltage Additional Items List of AdditionalItems Equipment Description Equipment Description Appendices Appendix contains the following chaptersAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal Meaning Brief description of the functional devices Wiring Examples SafeEthernet Protocol Ethernet Wiring ExampleElements of the network Networking Brief description of the functional devices Element Modbus serial Configuration of Ethernet Interfaces Communication SettingsFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Parameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OM Following table contains the parameter descriptions Parameter Description Brief description of the functional devices Glossary Functional block diagram Fault tolerance timeField bus See FTT Object linking and embedding OSI Model Open system interconnection modelProtective extra low voltage Programmable electronic system Safety extra low voltage Sequential function chartSafety integrity level according to IEC System-rack-slot Index Index