Equipment Description | Schneider Electric XPSMF2DO801 specs

Equipment Description

When using specified cables and plug connectors approved to 100 MHz, the maximum cable distance is 100 m (328.1 ft) with a maximum of six connector pairs. A combination of a plug and a socket is considered one pair.

Use optic fiber cables with converters for greater distances.

Using SafeEthernet protocol has the following advantages:

Very fast packet transfer between the collision areas

Significant increase of data throughput with full-duplex mode

Prevention of collisions allows deterministic operation.

33003405 07/2007

43

Image 43

Schneider Electric XPSMF2DO801 manual Equipment Description

Contents

07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance Appendices Procedure Safety InformationImportant Information Safety Information At a Glance About the Book 33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Module IntroductionRepresentation Front View Dimensions Remote output module Dimensions Side View Step Action InstallationProcedure Introduction HIMatrix 100 Compact device Cable duct Spacer = length of the spacer = height of the cable duct Installation with spacersLength of the required spacer is calculated as follows = H 40 mm / 1.57 HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Variable Description HousingInternal Convection Temperature range Temperature state Temperature State/Operating Overview Application and Function Stage XPSMF2DO801 safety remote output moduleInitial Operation Overview Application Function Terminal No Designation Function relay output Application and Function System CableDisconnection Following will occur Step Power Supply InterruptionLarge System Reconfiguration Voltage level Reaction of the controller SHORT-CIRCUIT Condition Short-Circuit Characteristics Output Channels Modules Offline Proof Test Offline Proof Periodic Proof TestingOffline Proof-Test Execution Chapter? Equipment DescriptionOutput module Whats in this XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Button Reset ButtonUsing Reset Housing, about 40...50 mm 1.57...1.97 in. from the left rim Communication via switches Overview Safety-Related CommunicationCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIO Maximum cable distance Following is a Ethernet cable connection diagramConnector pairs and cable distances Number Equipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Elements WiringEthernet Wiring Interface Recommended RJ45 ConnectorSwitches Class D capacity are required Description IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Interfaces OperationParameters Ethernet TCP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication UDP ports and usage For the next higher level and relies on the next lower level OSI model Number Layer Data Description Following table describes the seven OSI layers bottom-top Climatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Signal Line Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Power Supply Connectors Stripping Length and Torque Supply voltage Relay Outputs List of Additional Additional ItemsItems Equipment Description Equipment Description Chapter Chapter Name AppendicesAppendix contains the following chapters Appendix? Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error Codes Brief description of the functional devices Networking Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Elements of the network Brief description of the functional devices Modbus serial Element Flow-Control Mode list, select Autoneg Configuration of Ethernet InterfacesCommunication Settings For setting the communication parameters proceed as follows Konfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configuration Parameter Description Following table contains the parameter descriptions Brief description of the functional devices Glossary See FTT Functional block diagramFault tolerance time Field bus Programmable electronic system Object linking and embeddingOSI Model Open system interconnection model Protective extra low voltage System-rack-slot Safety extra low voltageSequential function chart Safety integrity level according to IEC Index Index