Manuals / Schneider Electric / Computer Equipment / Network Hardware

Schneider Electric XPSMF2DO801 manual IP Addressing and System ID, Description, Bit numbers e.g

Models: XPSMF2DO801

1 82

Download 82 pages 20.26 Kb

Page 49

Equipment Description

IP Addressing and System ID

Overview	A transparent label provided with the controller can be used to note the IP address
	and system ID (SRS, System-Rack-Slot) following a modification:
	IP_._._._SRS_._._
	Default value for IP address: 192.168.0.99
	Default value for SRS: 60000.1.0
	The ventilation slots in the housing of the Safety PLC must not be covered with the
	label.
	For more information about changing the IP address and system ID, see the
	XPSMFWIN Software manual.

	Note: Each Ethernet board has a unique Ethernet address. It is a 48 bit number:
	the first 24 bits indicate the manufacturer, while the last 24 bits are a unique
	number for each Ethernet board/controller-chip assigned by the manufacturer. The
	number is also called MAC ID.




TCP/IP	The IP address is an identifier for a device in a network. IP addresses are 32-bit
Description	numbers. To make it easier to memorize them, they are usually expressed in four
	8-bit numbers (e.g., 192.168.10.1)
	IP addresses are unique, no other device within the network can share the same
	address:
	the IP address assigned to the PC
	the part of the IP address (the subnet mask) that distinguishes other networks

	Note: The operator must ensure that the Ethernet used for Peer-to-Peer
	communication is adequately protected from unauthorized access (i.e. by
	hackers). The nature and extent of the measures to be taken must be determined
	in conjunction with the approval authorities.

33003405 07/2007

49

Image 49

Schneider Electric XPSMF2DO801 manual IP Addressing and System ID, Description, Bit numbers e.g

Contents

07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance Appendices Procedure Safety InformationImportant Information Safety Information At a Glance About the Book 33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Representation IntroductionFront View Module Dimensions Remote output module Dimensions Side View Procedure InstallationIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Length of the required spacer is calculated as follows Installation with spacers= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Internal HousingConvection Variable Description Temperature range Temperature state Temperature State/Operating Overview Application and Function Initial Operation XPSMF2DO801 safety remote output moduleOverview Stage Application Function Terminal No Designation Function relay output Application and Function Disconnection CableFollowing will occur System Large System Reconfiguration Power Supply InterruptionVoltage level Reaction of the controller Step SHORT-CIRCUIT Condition Short-Circuit Characteristics Output Channels Modules Offline Proof Test Offline Proof-Test Periodic Proof TestingExecution Offline Proof Output module Equipment DescriptionWhats in this Chapter? XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Using Reset Reset ButtonHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Communication via switches Overview Safety-Related CommunicationCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIO Connector pairs and cable distances Following is a Ethernet cable connection diagramNumber Maximum cable distance Equipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Ethernet Wiring WiringInterface Elements Switches RJ45 ConnectorClass D capacity are required Recommended Description IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Parameters OperationEthernet Interfaces Used Network Ports for Ethernet Communication Connections for SafeEthernet/ Networking ExamplesUDP ports and usage TCP ports and usage For the next higher level and relies on the next lower level OSI model Number Layer Data Description Following table describes the seven OSI layers bottom-top Climatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Mechanical Data Power Supply Connectors Technical CharacteristicsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Supply voltage Relay Outputs List of Additional Additional ItemsItems Equipment Description Equipment Description Appendix contains the following chapters AppendicesAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error Codes Brief description of the functional devices SafeEthernet Protocol Ethernet Wiring Example Wiring ExamplesElements of the network Networking Brief description of the functional devices Modbus serial Element Communication Settings Configuration of Ethernet InterfacesFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Konfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configuration Parameter Description Following table contains the parameter descriptions Brief description of the functional devices Glossary Fault tolerance time Functional block diagramField bus See FTT OSI Model Open system interconnection model Object linking and embeddingProtective extra low voltage Programmable electronic system Sequential function chart Safety extra low voltageSafety integrity level according to IEC System-rack-slot Index Index