Parameters of a port configuration | Schneider Electric XPSMF2DO801

Brief description of the functional devices

Port Settings The port settings of the integrated switch can be parameterized individually from COM OS version > 8.32 and XPSMFWIN Hardware Management version

>7.56.10. Using the context menu of the communication COM settings select Ethernet switch → New → Port configuration. A configuration menu can be established for each switched port.

Setting a port configuration

	[0] HIMatrix F35
	COM
	Ethernet switch	New
	CPU	New	Port configuration
	CPU	Copy	Port configuration
	[1] DO 8 DO 8	Copy
	[1] DO 8 DO 8
	[2] CI 2 CI 2	Past
	[3] MI 24/8 FS1000 MIDelete24/8 FS1000
	[3] Auswahl	Print...
	Auswahl	Properties
	Protocols

Parameters of a port configuration

	Applikationen-Factory-V1.1	/Konfiguration/Abl-Mode/HIMatrix F35/OM
	Konfiguration	Type		Port configuration
	[0] HIMatrix F3 DIO 20_8 01_1	Type		Port configuration
	[0] HIMatrix F3 DIO 20_8 01_2	Name		Port configuration_1
	[250] Ablauf	Name		Port configuration_1
	[250] Ablauf	Port		1
	[33] Abl-Mode	Port		1
	Abl-Mode	Speed [MBit/s]		100
	Protocols	Speed [MBit/s]		100
	Protocols	Flow control		Full duplex
	Remote I/O	Flow control		Full duplex
	[0] HIMatrix F35	Autoneg also with fix values
	COM	Limit		Broadcast
	Ethernet switch	Limit		Broadcast
	Ethernet switch
	Port configuration_1	OK	Cancel	Apply	Help
	CPU	OK	Cancel	Apply	Help
	CPU

74	33003405 07/2007

Image 74

Schneider Electric XPSMF2DO801 manual Parameters of a port configuration, Konfiguration/Abl-Mode/HIMatrix F35/OM

Contents

XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a Glance Important Information Safety InformationProcedure Safety Information About the Book At a Glance 33003405 07/2007 Topic Overview XPSMF2DO801Overview Whats in this Chapter? Front View IntroductionRepresentation Module Dimensions Dimensions Remote output module Side View Introduction InstallationProcedure Step Action HIMatrix 100 Compact device Cable duct Spacer = H 40 mm / 1.57 Installation with spacersLength of the required spacer is calculated as follows = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Convection HousingInternal Variable Description Temperature State/Operating Temperature range Temperature state Overview Application and Function Overview XPSMF2DO801 safety remote output moduleInitial Operation Stage Application Function Terminal No Designation Function relay output Application and Function Following will occur CableDisconnection System Voltage level Reaction of the controller Power Supply InterruptionLarge System Reconfiguration Step Short-Circuit Characteristics Output Channels SHORT-CIRCUIT Condition Modules Offline Proof Test Execution Periodic Proof TestingOffline Proof-Test Offline Proof Whats in this Equipment DescriptionOutput module Chapter? Elements of the front panel Housing ElementsXPSMF2DO801 safety remote output module Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Housing, about 40...50 mm 1.57...1.97 in. from the left rim Reset ButtonUsing Reset Button Communication Overview Safety-Related CommunicationCommunication via switches HIMatrix F3AIO Following scheme shows a SafeEthernet networking example Number Following is a Ethernet cable connection diagramConnector pairs and cable distances Maximum cable distance Equipment Description LEDs Color Status Meaning LED DescriptionFollowing table describes behaviors of the LEDs LED Interface WiringEthernet Wiring Elements Class D capacity are required RJ45 ConnectorSwitches Recommended Bit numbers e.g IP Addressing and System IDDescription SafeEthernet 33003405 07/2007 Ethernet OperationParameters Interfaces UDP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication TCP ports and usage OSI model For the next higher level and relies on the next lower level Following table describes the seven OSI layers bottom-top Number Layer Data Description Conditions Operating ConditionsClimatic Following tables MechanicalEMC Conditions Equipment Description Power Supply Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Signal Line Connectors Stripping Length and Torque Relay Outputs Supply voltage Items Additional ItemsList of Additional Equipment Description Equipment Description Appendix? AppendicesAppendix contains the following chapters Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal Meaning Brief description of the functional devices Elements of the network Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Networking Brief description of the functional devices Element Modbus serial For setting the communication parameters proceed as follows Configuration of Ethernet InterfacesCommunication Settings Flow-Control Mode list, select Autoneg Parameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OM Following table contains the parameter descriptions Parameter Description Brief description of the functional devices Glossary Field bus Functional block diagramFault tolerance time See FTT Protective extra low voltage Object linking and embeddingOSI Model Open system interconnection model Programmable electronic system Safety integrity level according to IEC Safety extra low voltageSequential function chart System-rack-slot Index Index