Schneider Electric XPSMF2DO801 guide

						Brief description of the functional devices

System signal		R/W		Meaning

DO[xx].Error Code [BYTE]		W		error codes of the digital output channels

				0x01	error in digital output module
				0x04	error reading back the digital outputs
				0x10	error reading back relay [x].1
					(the channel is permanently deactivated)
				0x20	error reading back relay [x].2
					(the channel is permanently deactivated)
				0x080	channel still can not be activated after deactivation by
						application
						forcing
						channel/module failure

DO[xx].Value [BOOL]		W		output value of digital output channels

				0	output power-free
				1	output activated

33003405 07/2007

69

Image 69

Schneider Electric XPSMF2DO801 manual Brief description of the functional devices

Contents

07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance Appendices Safety Information ProcedureImportant Information Safety Information At a Glance About the Book 33003405 07/2007 Overview XPSMF2DO801 Overview Whats in this Chapter?Topic Representation IntroductionFront View Module Dimensions Remote output module Dimensions Side View Procedure InstallationIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Length of the required spacer is calculated as follows Installation with spacers= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Internal HousingConvection Variable Description Temperature range Temperature state Temperature State/Operating Overview Application and Function Initial Operation XPSMF2DO801 safety remote output moduleOverview Stage Application Function Terminal No Designation Function relay output Application and Function Disconnection CableFollowing will occur System Large System Reconfiguration Power Supply InterruptionVoltage level Reaction of the controller Step SHORT-CIRCUIT Condition Short-Circuit Characteristics Output Channels Modules Offline Proof Test Offline Proof-Test Periodic Proof TestingExecution Offline Proof Output module Equipment DescriptionWhats in this Chapter? Housing Elements XPSMF2DO801 safety remote output moduleElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Using Reset Reset ButtonHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Overview Safety-Related Communication Communication via switchesCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIO Connector pairs and cable distances Following is a Ethernet cable connection diagramNumber Maximum cable distance Equipment Description LEDs LED Description Following table describes behaviors of the LEDsColor Status Meaning LED Ethernet Wiring WiringInterface Elements Switches RJ45 ConnectorClass D capacity are required Recommended IP Addressing and System ID DescriptionBit numbers e.g SafeEthernet 33003405 07/2007 Parameters OperationEthernet Interfaces Used Network Ports for Ethernet Communication Connections for SafeEthernet/ Networking ExamplesUDP ports and usage TCP ports and usage For the next higher level and relies on the next lower level OSI model Number Layer Data Description Following table describes the seven OSI layers bottom-top Operating Conditions ClimaticConditions Mechanical EMC ConditionsFollowing tables Equipment Description Mechanical Data Power Supply Connectors Technical CharacteristicsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Supply voltage Relay Outputs Additional Items List of AdditionalItems Equipment Description Equipment Description Appendix contains the following chapters AppendicesAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error Codes Brief description of the functional devices SafeEthernet Protocol Ethernet Wiring Example Wiring ExamplesElements of the network Networking Brief description of the functional devices Modbus serial Element Communication Settings Configuration of Ethernet InterfacesFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Konfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configuration Parameter Description Following table contains the parameter descriptions Brief description of the functional devices Glossary Fault tolerance time Functional block diagramField bus See FTT OSI Model Open system interconnection model Object linking and embeddingProtective extra low voltage Programmable electronic system Sequential function chart Safety extra low voltageSafety integrity level according to IEC System-rack-slot Index Index