Equipment Description | Schneider Electric XPSMF2DO801 specs

Equipment Description

Voltage Supply The most important tests and limit values for the voltage supply of the equipment are listed in the following table:

	IEC/EN 61131-2	Verification of DC Power Supply Characteristics

		The power supply must meet alternatively the following
		standards: IEC 61131-2 or SELV (Safety Extra Low
		Voltage) or PELV (Protective Extra Low Voltage)

		Fusing the XPSMF2DO801 safety remote output device
		must be performed according to this manual only.

	6.3.7.1.1	Voltage range test: 24 V DC, -20% to 25% (19.2 V DC to
		30.0 V DC)

	6.3.7.2.1	Momentary interruption immunity test: DC, PS 2: 10ms

	6.3.7.4.1	Reversal of DC power supply polarity test

	6.3.7.5.1	Backup duration withstand test: Test B, 1000 h, Lithium
		battery is used for backup.

58	33003405 07/2007

Image 58

Schneider Electric XPSMF2DO801 manual Equipment Description

Contents

XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a Glance Procedure Safety InformationImportant Information Safety Information About the Book At a Glance 33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Front View IntroductionRepresentation Module Dimensions Dimensions Remote output module Side View Introduction InstallationProcedure Step Action HIMatrix 100 Compact device Cable duct Spacer = H 40 mm / 1.57 Installation with spacersLength of the required spacer is calculated as follows = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Convection HousingInternal Variable Description Temperature State/Operating Temperature range Temperature state Overview Application and Function Overview XPSMF2DO801 safety remote output moduleInitial Operation Stage Application Function Terminal No Designation Function relay output Application and Function Following will occur CableDisconnection System Voltage level Reaction of the controller Power Supply InterruptionLarge System Reconfiguration Step Short-Circuit Characteristics Output Channels SHORT-CIRCUIT Condition Modules Offline Proof Test Execution Periodic Proof TestingOffline Proof-Test Offline Proof Whats in this Equipment DescriptionOutput module Chapter? XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Housing, about 40...50 mm 1.57...1.97 in. from the left rim Reset ButtonUsing Reset Button Communication via switches Overview Safety-Related CommunicationCommunication HIMatrix F3AIO Following scheme shows a SafeEthernet networking example Number Following is a Ethernet cable connection diagramConnector pairs and cable distances Maximum cable distance Equipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Interface WiringEthernet Wiring Elements Class D capacity are required RJ45 ConnectorSwitches Recommended Description IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Ethernet OperationParameters Interfaces UDP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication TCP ports and usage OSI model For the next higher level and relies on the next lower level Following table describes the seven OSI layers bottom-top Number Layer Data Description Climatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Power Supply Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Signal Line Connectors Stripping Length and Torque Relay Outputs Supply voltage List of Additional Additional ItemsItems Equipment Description Equipment Description Appendix? AppendicesAppendix contains the following chapters Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal Meaning Brief description of the functional devices Elements of the network Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Networking Brief description of the functional devices Element Modbus serial For setting the communication parameters proceed as follows Configuration of Ethernet InterfacesCommunication Settings Flow-Control Mode list, select Autoneg Parameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OM Following table contains the parameter descriptions Parameter Description Brief description of the functional devices Glossary Field bus Functional block diagramFault tolerance time See FTT Protective extra low voltage Object linking and embeddingOSI Model Open system interconnection model Programmable electronic system Safety integrity level according to IEC Safety extra low voltageSequential function chart System-rack-slot Index Index