Reset Button, Using Reset, Effect | Schneider Electric XPSMF2DO801

	Equipment Description
Reset Button



Overview	The device is equipped with a reset button. The reset button is used if the PC
	connection password is lost.



Using Reset	You can access the pushbutton through a small round opening on the upper side of
Button	the housing, about 40...50 mm (1.57...1.97 in.) from the left rim.
	Use the button only while you reboot the device and keep the button pressed for at
	least 20 s. Pushing the reset button while the device is running produces no result.



Effect	When you push the Reset button,
	all accounts are deactivated (except the default Administrator account
	without password) and
	IP addresses and system ID (SRS) are set to default values.

	Note: After activation of the reset button, values are modified and remain valid until
	the next reboot. After the next reboot the previous values are restored. You can
	enter new information, if necessary.

33003405 07/2007

39

Image 39

Schneider Electric XPSMF2DO801 Reset Button, Using Reset, Housing, about 40...50 mm 1.57...1.97 in. from the left rim

Contents

07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance Appendices Safety Information ProcedureImportant Information Safety Information At a Glance About the Book 33003405 07/2007 Overview XPSMF2DO801 Overview Whats in this Chapter?Topic Module IntroductionRepresentation Front View Dimensions Remote output module Dimensions Side View Step Action InstallationProcedure Introduction HIMatrix 100 Compact device Cable duct Spacer = length of the spacer = height of the cable duct Installation with spacersLength of the required spacer is calculated as follows = H 40 mm / 1.57 HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Variable Description HousingInternal Convection Temperature range Temperature state Temperature State/Operating Overview Application and Function Stage XPSMF2DO801 safety remote output moduleInitial Operation Overview Application Function Terminal No Designation Function relay output Application and Function System CableDisconnection Following will occur Step Power Supply InterruptionLarge System Reconfiguration Voltage level Reaction of the controller SHORT-CIRCUIT Condition Short-Circuit Characteristics Output Channels Modules Offline Proof Test Offline Proof Periodic Proof TestingOffline Proof-Test Execution Chapter? Equipment DescriptionOutput module Whats in this Housing Elements XPSMF2DO801 safety remote output moduleElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Button Reset ButtonUsing Reset Housing, about 40...50 mm 1.57...1.97 in. from the left rim Overview Safety-Related Communication Communication via switchesCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIO Maximum cable distance Following is a Ethernet cable connection diagramConnector pairs and cable distances Number Equipment Description LEDs LED Description Following table describes behaviors of the LEDsColor Status Meaning LED Elements WiringEthernet Wiring Interface Recommended RJ45 ConnectorSwitches Class D capacity are required IP Addressing and System ID DescriptionBit numbers e.g SafeEthernet 33003405 07/2007 Interfaces OperationParameters Ethernet TCP ports and usage Connections for SafeEthernet/ Networking ExamplesUsed Network Ports for Ethernet Communication UDP ports and usage For the next higher level and relies on the next lower level OSI model Number Layer Data Description Following table describes the seven OSI layers bottom-top Operating Conditions ClimaticConditions Mechanical EMC ConditionsFollowing tables Equipment Description Signal Line Connectors Technical CharacteristicsMechanical Data Power Supply Connectors Power Supply Connectors Stripping Length and Torque Supply voltage Relay Outputs Additional Items List of AdditionalItems Equipment Description Equipment Description Chapter Chapter Name AppendicesAppendix contains the following chapters Appendix? Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error Codes Brief description of the functional devices Networking Wiring ExamplesSafeEthernet Protocol Ethernet Wiring Example Elements of the network Brief description of the functional devices Modbus serial Element Flow-Control Mode list, select Autoneg Configuration of Ethernet InterfacesCommunication Settings For setting the communication parameters proceed as follows Konfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configuration Parameter Description Following table contains the parameter descriptions Brief description of the functional devices Glossary See FTT Functional block diagramFault tolerance time Field bus Programmable electronic system Object linking and embeddingOSI Model Open system interconnection model Protective extra low voltage System-rack-slot Safety extra low voltageSequential function chart Safety integrity level according to IEC Index Index