33003405 07/2007 | Schneider Electric XPSMF2DO801 specs

About the Book

The corresponding programming software is XPSMFWIN. The software is executable in the Microsoft Windows 2000/XP. The software helps the user to create safety-related programs and operate the Programmable Electronic System (PES).

Note: The declaration of conformity is provided within the hardware product’s packaging. All devices are labelled with the CE sign.

Product Related Schneider Electric assumes no responsibility for any errors that may appear in this

Warnings document. If you have suggestions for improvements or amendments or have found errors in this publication, please notify us.

No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Schneider Electric.

All pertinent state, regional, and local safety regulations must be observed when installing and using this product. For reasons of safety and to ensure compliance with documented system data, only the manufacturer should perform repairs to components.

Failure to use Schneider Electric software or approved software with our hardware products may result in injury, harm, or improper operating results.

Failure to observe this product’s safety-related warning can result in injury or equipment damage.

User Comments We welcome your comments about this document. You can reach us by e-mail at techpub@schneider-electric.com

8	33003405 07/2007

Image 8

Schneider Electric XPSMF2DO801 manual 33003405 07/2007

Contents

XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a Glance Important Information Safety InformationProcedure Safety Information About the Book At a Glance 33003405 07/2007 Topic Overview XPSMF2DO801Overview Whats in this Chapter? Introduction RepresentationFront View Module Dimensions Dimensions Remote output module Side View Installation ProcedureIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Installation with spacers Length of the required spacer is calculated as follows= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Housing InternalConvection Variable Description Temperature State/Operating Temperature range Temperature state Overview Application and Function XPSMF2DO801 safety remote output module Initial OperationOverview Stage Application Function Terminal No Designation Function relay output Application and Function Cable DisconnectionFollowing will occur System Power Supply Interruption Large System ReconfigurationVoltage level Reaction of the controller Step Short-Circuit Characteristics Output Channels SHORT-CIRCUIT Condition Modules Offline Proof Test Periodic Proof Testing Offline Proof-TestExecution Offline Proof Equipment Description Output moduleWhats in this Chapter? Elements of the front panel Housing ElementsXPSMF2DO801 safety remote output module Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Reset Button Using ResetHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Communication Overview Safety-Related CommunicationCommunication via switches HIMatrix F3AIO Following scheme shows a SafeEthernet networking example Following is a Ethernet cable connection diagram Connector pairs and cable distancesNumber Maximum cable distance Equipment Description LEDs Color Status Meaning LED DescriptionFollowing table describes behaviors of the LEDs LED Wiring Ethernet WiringInterface Elements RJ45 Connector SwitchesClass D capacity are required Recommended Bit numbers e.g IP Addressing and System IDDescription SafeEthernet 33003405 07/2007 Operation ParametersEthernet Interfaces Connections for SafeEthernet/ Networking Examples Used Network Ports for Ethernet CommunicationUDP ports and usage TCP ports and usage OSI model For the next higher level and relies on the next lower level Following table describes the seven OSI layers bottom-top Number Layer Data Description Conditions Operating ConditionsClimatic Following tables MechanicalEMC Conditions Equipment Description Technical Characteristics Mechanical Data Power Supply ConnectorsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Relay Outputs Supply voltage Items Additional ItemsList of Additional Equipment Description Equipment Description Appendices Appendix contains the following chaptersAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal Meaning Brief description of the functional devices Wiring Examples SafeEthernet Protocol Ethernet Wiring ExampleElements of the network Networking Brief description of the functional devices Element Modbus serial Configuration of Ethernet Interfaces Communication SettingsFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Parameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OM Following table contains the parameter descriptions Parameter Description Brief description of the functional devices Glossary Functional block diagram Fault tolerance timeField bus See FTT Object linking and embedding OSI Model Open system interconnection modelProtective extra low voltage Programmable electronic system Safety extra low voltage Sequential function chartSafety integrity level according to IEC System-rack-slot Index Index