Communication Settings | Schneider Electric XPSMF2DO801 specs

Brief description of the functional devices

Configuration of Ethernet Interfaces

Communication Settings

For setting the communication parameters proceed as follows:

Step

Action

1Open the Extended tab.

2In the Speed Mode list, select Autoneg.

3In the Flow-Control Mode list, select Autoneg.

4Select the Activate Extended Settings check box. Result: The selected parameters are activated.

Konfiguration	/Konfiguration/Abl-Mode/HIMatrix F35/COM
[0] HIMatrix F3 DIO 20_8 01_1	IP Settings	Extended License Key
[0] HIMatrix F3 DIO 20_8 01_2	IP Settings	Extended License Key
[250] Ablauf	Activate Extended ...
[33] Abl-Mode	Activate Extended ...		00
Abl-Mode	ARP Aging Time [s]		00
Protocols	MAC Learning		conservative
Remote I/O	MAC Learning		conservative
Remote I/O	IP Forwarding
[0] HIMatrix F35	IP Forwarding		Autoneg
COM	Speed Mode		Autoneg
Ethernet switch	Flow-Control Mode
Port configuration_1	Flow-Control Mode
CPU
[1] DO 8 DO 8
[2] CI 2 CI 2
[3] MI 24/8 FS1000 MI 24/800	OK	Cancel	Apply	Help
	OK	Cancel	Apply	Help

Note: The parameters of the Extended tab are explained in detail in the online help of XPSMFWIN.

33003405 07/2007

73

Image 73

Schneider Electric XPSMF2DO801 manual Configuration of Ethernet Interfaces, Communication Settings

Contents

07/2007 XPSMF2DO801 Remote Output Module Hardware ManualPage Table of Contents At a Glance Appendices Procedure Safety InformationImportant Information Safety Information At a Glance About the Book 33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Representation IntroductionFront View Module Dimensions Remote output module Dimensions Side View Procedure InstallationIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Length of the required spacer is calculated as follows Installation with spacers= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Internal HousingConvection Variable Description Temperature range Temperature state Temperature State/Operating Overview Application and Function Initial Operation XPSMF2DO801 safety remote output moduleOverview Stage Application Function Terminal No Designation Function relay output Application and Function Disconnection CableFollowing will occur System Large System Reconfiguration Power Supply InterruptionVoltage level Reaction of the controller Step SHORT-CIRCUIT Condition Short-Circuit Characteristics Output Channels Modules Offline Proof Test Offline Proof-Test Periodic Proof TestingExecution Offline Proof Output module Equipment DescriptionWhats in this Chapter? XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Using Reset Reset ButtonHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Communication via switches Overview Safety-Related CommunicationCommunication Following scheme shows a SafeEthernet networking example HIMatrix F3AIO Connector pairs and cable distances Following is a Ethernet cable connection diagramNumber Maximum cable distance Equipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Ethernet Wiring WiringInterface Elements Switches RJ45 ConnectorClass D capacity are required Recommended Description IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Parameters OperationEthernet Interfaces Used Network Ports for Ethernet Communication Connections for SafeEthernet/ Networking ExamplesUDP ports and usage TCP ports and usage For the next higher level and relies on the next lower level OSI model Number Layer Data Description Following table describes the seven OSI layers bottom-top Climatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Mechanical Data Power Supply Connectors Technical CharacteristicsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Supply voltage Relay Outputs List of Additional Additional ItemsItems Equipment Description Equipment Description Appendix contains the following chapters AppendicesAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes System signal Meaning Error Codes Brief description of the functional devices SafeEthernet Protocol Ethernet Wiring Example Wiring ExamplesElements of the network Networking Brief description of the functional devices Modbus serial Element Communication Settings Configuration of Ethernet InterfacesFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Konfiguration/Abl-Mode/HIMatrix F35/OM Parameters of a port configuration Parameter Description Following table contains the parameter descriptions Brief description of the functional devices Glossary Fault tolerance time Functional block diagramField bus See FTT OSI Model Open system interconnection model Object linking and embeddingProtective extra low voltage Programmable electronic system Sequential function chart Safety extra low voltageSafety integrity level according to IEC System-rack-slot Index Index