Operation, Parameters, Ethernet | Schneider Electric XPSMF2DO801

Equipment Description

Operation	Up to COM OS version 8.32 all Ethernet ports of the integrated Ethernet switches
Parameters of	have the same settings:
the Ethernet		Autoneg/Autoneg for Speed Mode
Interfaces		Flow-control Mode
	Other settings are not possible and will be rejected by the PLC when loading a
	configuration.
	The Ethernet interfaces 10/100 BaseT of the device have the following parameters:

	Firm operating parameters

	Speed Mode		Autoneg

	Flow-Control Mode		Autoneg

Other devices combined with the Safety PLC or remote I/O device must have the following network settings:

Admissible settings of other devices

Speed Mode	Autoneg

Flow-Control Mode	Autoneg

or

Speed Mode	Autoneg

Flow-Control Mode	Half Duplex

or

Speed Mode	10 or 100 Mbit/s

Flow-Control Mode	Half Duplex


Non-admissible settings of other devices

Speed Mode	Autoneg or 10 or 100 Mbit/s

Flow-Control Mode	Full Duplex

For COM OS version > 8.32 and XPSMFWIN Hardware Management version

>7.56.10 each Ethernet port of the integrated switch can be individually configured. See also in the appendix Connection Diagrams, Examples of Application, and Error Codes, p. 67.

52	33003405 07/2007

Image 52

Schneider Electric XPSMF2DO801 manual Operation, Parameters, Ethernet, Interfaces

Contents

XPSMF2DO801 Remote Output Module Hardware Manual 07/2007Page Table of Contents Appendices At a Glance Procedure Safety InformationImportant Information Safety Information About the Book At a Glance 33003405 07/2007 Overview Whats in this Chapter? Overview XPSMF2DO801Topic Introduction RepresentationFront View Module Dimensions Dimensions Remote output module Side View Installation ProcedureIntroduction Step Action HIMatrix 100 Compact device Cable duct Spacer Installation with spacers Length of the required spacer is calculated as follows= H 40 mm / 1.57 = length of the spacer = height of the cable duct HIMatrix F31 Heat Case installation Calculation of a m2 1m2=10.76ft2 Housing InternalConvection Variable Description Temperature State/Operating Temperature range Temperature state Overview Application and Function XPSMF2DO801 safety remote output module Initial OperationOverview Stage Application Function Terminal No Designation Function relay output Application and Function Cable DisconnectionFollowing will occur System Power Supply Interruption Large System ReconfigurationVoltage level Reaction of the controller Step Short-Circuit Characteristics Output Channels SHORT-CIRCUIT Condition Modules Offline Proof Test Periodic Proof Testing Offline Proof-TestExecution Offline Proof Equipment Description Output moduleWhats in this Chapter? XPSMF2DO801 safety remote output module Housing ElementsElements of the front panel Top View Following image shows the elements of the top panel Back Panel Following image shows elements of the back panel Reset Button Using ResetHousing, about 40...50 mm 1.57...1.97 in. from the left rim Button Communication via switches Overview Safety-Related CommunicationCommunication HIMatrix F3AIO Following scheme shows a SafeEthernet networking example Following is a Ethernet cable connection diagram Connector pairs and cable distancesNumber Maximum cable distance Equipment Description LEDs Following table describes behaviors of the LEDs LED DescriptionColor Status Meaning LED Wiring Ethernet WiringInterface Elements RJ45 Connector SwitchesClass D capacity are required Recommended Description IP Addressing and System IDBit numbers e.g SafeEthernet 33003405 07/2007 Operation ParametersEthernet Interfaces Connections for SafeEthernet/ Networking Examples Used Network Ports for Ethernet CommunicationUDP ports and usage TCP ports and usage OSI model For the next higher level and relies on the next lower level Following table describes the seven OSI layers bottom-top Number Layer Data Description Climatic Operating ConditionsConditions EMC Conditions MechanicalFollowing tables Equipment Description Technical Characteristics Mechanical Data Power Supply ConnectorsPower Supply Connectors Signal Line Connectors Stripping Length and Torque Relay Outputs Supply voltage List of Additional Additional ItemsItems Equipment Description Equipment Description Appendices Appendix contains the following chaptersAppendix? Chapter Chapter Name Appendices Connection Diagrams, Examples Application, and Error Codes Error Codes System signal Meaning Brief description of the functional devices Wiring Examples SafeEthernet Protocol Ethernet Wiring ExampleElements of the network Networking Brief description of the functional devices Element Modbus serial Configuration of Ethernet Interfaces Communication SettingsFor setting the communication parameters proceed as follows Flow-Control Mode list, select Autoneg Parameters of a port configuration Konfiguration/Abl-Mode/HIMatrix F35/OM Following table contains the parameter descriptions Parameter Description Brief description of the functional devices Glossary Functional block diagram Fault tolerance timeField bus See FTT Object linking and embedding OSI Model Open system interconnection modelProtective extra low voltage Programmable electronic system Safety extra low voltage Sequential function chartSafety integrity level according to IEC System-rack-slot Index Index