Editing and clearing auto-dial numbers | Sharp UX-P400 manual

Sending a Fax by Automatic Dialling

Editing and clearing auto-dial numbers

If you need to make changes to a previously stored auto-dial number, or clear a number, follow these steps:

1 Press FUNKTION once and	once.	Display:

<NEW NUMBER>

2 Press or until the number you wish to edit or clear appears in the display.

3	Press	once.	1=EDIT, 2=CLEAR
			1=EDIT, 2=CLEAR
4	Select EDIT or CLEAR:
	EDIT: 1	CLEAR: 2

•If you selected CLEAR, go to Step 8.

5 If you selected EDIT, make the desired changes to the number.

•Press or to move the cursor to the digit or digits you wish to change, and then enter the new digit. The new digit will replace the old digit.

•If you do not wish to change the number, go directly to Step 6.

6 START/ Press SPEICHER

7 Make the desired changes to the name.

•Press or to move the cursor to the letter or letters you wish to change, and then press the appropriate number key repeatedly until the desired letter appears (see Step 5 on page 32). The new letter will replace the old letter.

•If you do not wish to change the name, go directly to Step 8.

Sending	Faxes
2.

33

Image 35

Sharp UX-P400 Editing and clearing auto-dial numbers, Select Edit or Clear, Make the desired changes to the name

Contents

UX-P400/NX-P500 Aviso Display Introduction Intended use Important safety information Table of Contents Answering Machine Connection Look at the Operation Panel Key COPY/HELP/POLL keySTART/MEMORY key Function key About condensation InstallationUnpacking Checklist Points to keep in mind when setting up Connections Connecting the handsetConnecting the power cord Connecting the telephone line cord Switzerland, Austria Attach the paper tray and paper tray extensionOther devices Germany Loading the Imaging Film Compartment Remove the new roll of imaging film from its packagingInsert the green gears Insert the film into the print Insert the stack of paper into the tray, Print Side Down Loading Printing Paper Print contrast setting Press Funktion once Twice Entering Your Name and Fax Number Press Stop to return to the date and time display Enter a two-digit number for the day 01 to Example the 5th Setting the Date and TimePress once and once To start the clock Enter the year four digitsExample 2001 Mode Setting the Reception ModeSetting the reception mode TEL/FAX mode Press Until the display Volume AdjustmentShows the desired volume level Speaker If you selected Ringer OFF OK ? Ringer Flash Select Setting for PBX Press Funktion once Once Setting the Display Language Transmittable Documents Size and weightSending Faxes Other restrictions Loading the Document Resolution settings Adjusting the Resolution and Contrast One or more times until Contrast settingsLoad the documents Sending a Fax by Normal Dialling When transmission is completed, the fax will beep once Press Funktion once Sending a Fax by Automatic DiallingStoring fax and phone numbers for automatic dialling Press Speicher Make the desired changes to the name Editing and clearing auto-dial numbersSelect Edit or Clear If you are sending a fax, load the documents Using an auto-dial numberReturn to to edit or clear another number, or press Stop to Return to the date and time display Sending a fax by Direct Keypad Dialling Automatic redialling Redial Empfang to set Sending a Fax From MemoryBroadcasting sending a fax to multiple destinations If the memory becomes full Memory transmission Empfang until the arrow Using TEL/FAX ModePseudo Ring Duration for Tel/Fax Mode Receiving Faxes Enter a number as follows for the desired duration Using A.M. ModePress once and 3 times Press Funktion once and once Using FAX ModeChanging the number of rings Number from 2 to Using TEL ModeEnter the desired number of rings any Replace the handset Answering with the fax’s handset Phone goes dead Fax Signal Receive Optional Reception Settings Enter the desired number any number from 0 to Example 3 Changing the number for remote fax activationPress To turn on the function, or To turn it off Select 100% Reception RatioPress To select AUTO, or 2 to Substitute Reception to Memory Load the documents face down. Maximum of 10 pages Making Copies Copy Cut-off Comments Answering Machine ConnectionPreparations Changing the outgoing message Set your answering machine to auto answer Using the Answering Machine ConnectionSet the reception mode to A.M Quiet Detect Time Optional A.M. Mode SettingsHow answering machine mode operates Quiet Time On A.M. Failure Quiet Start Quiet Detect Start Time To turn off Caller ID, press Caller ID Requires Subscription to ServiceSpecial Functions Press YES to turn on Caller ID Display messages How Caller ID operates Dialling and transmission begin Fax Press Stop when you have finished viewing the listViewing the Caller ID list Press Twice Press Speicher to store or clear the number To delete calls from the Caller ID listPriority Call Blocking voice calls Press once and twice Blocking Reception of Unwanted FaxesPress Funktion once and twice Press Abruf Polling Requesting a Fax Transmission Transferring calls PBX operationsMaking enquiry calls Caller-ID List Setup ListPrinting Lists Telephone Number List Headings in Transaction Report Transaction Report Help List Transaction Report print condition Print head Maintenance Scanning glass and rollers Maintenance If the scanning glass is difficult to clean Housing Problem Solution TroubleshootingProblems and Solutions Line error Correct socket. See Connecting the handset on Dialling and transmission problems Reception and copying problems Answering machine connection See Loading the Imaging Film on General problems Press Start KEY Messages and Signals Substitute Reception to Memory on page 48. If you Recalling Audible signals Clearing a jammed document Clearing Paper Jams Clearing jammed printing paper Sending Faxes Quick Reference Guide Index Index Page Sharp Electronics Europe Gmbh