Quiet Detect Start Time, Quiet Start | Sharp UX-P400 specs

Optional A.M. Mode Settings

Quiet Detect Start Time

This setting can be used to delay the start of the Quiet Detect Time function. For example, if you want to insert a pause at the beginning of your answering machine’s outgoing message to ensure clear detection of fax signals, you can use this setting to delay the start of silence detection so that the pause will not cause the fax to take over the line.

Quiet Detect Start Timing has been turned off at the factory. If you want to use this function, turn it on by entering a 2-digit number equal to the desired number of seconds of the delay. As general guide, the delay time should be slightly longer than the pause before the outgoing message.

1	Press FUNKTION once and		Display:
1	Press FUNKTION once and		once.
			OPTION SETTING
2	Press	once and	5 times.
			QUIET START
3	Press	once.	ENTER (00-15) 00
			ENTER (00-15) 00

4 Enter a 2-digit number (from 01 to 15)

for the number of seconds of the delay, or enter 00 to turn off the function.

Example: 5 seconds 0

5

The display briefly shows your selection, then:

ON A.M. FAILURE

5 Press STOP to return to the date and time display.

56

Image 58

Sharp UX-P400 operation manual Quiet Detect Start Time, Quiet Start

Contents

UX-P400/NX-P500 Aviso Introduction Display Intended use Important safety information Table of Contents Answering Machine Connection Look at the Operation Panel Function key COPY/HELP/POLL keySTART/MEMORY key Key Points to keep in mind when setting up InstallationUnpacking Checklist About condensation Connecting the power cord Connecting the handsetConnections Connecting the telephone line cord Germany Attach the paper tray and paper tray extensionOther devices Switzerland, Austria Loading the Imaging Film Insert the film into the print Remove the new roll of imaging film from its packagingInsert the green gears Compartment Loading Printing Paper Insert the stack of paper into the tray, Print Side Down Print contrast setting Entering Your Name and Fax Number Press Funktion once Twice Press Stop to return to the date and time display Press once and once Setting the Date and TimeEnter a two-digit number for the day 01 to Example the 5th Example 2001 Enter the year four digitsTo start the clock TEL/FAX mode Setting the Reception ModeSetting the reception mode Mode Speaker Volume AdjustmentShows the desired volume level Press Until the display Ringer If you selected Ringer OFF OK ? Flash Select Setting for PBX Setting the Display Language Press Funktion once Once Sending Faxes Size and weightTransmittable Documents Loading the Document Other restrictions Adjusting the Resolution and Contrast Resolution settings Load the documents Contrast settingsOne or more times until Sending a Fax by Normal Dialling When transmission is completed, the fax will beep once Storing fax and phone numbers for automatic dialling Sending a Fax by Automatic DiallingPress Funktion once Press Speicher Select Edit or Clear Editing and clearing auto-dial numbersMake the desired changes to the name Return to the date and time display Using an auto-dial numberReturn to to edit or clear another number, or press Stop to If you are sending a fax, load the documents Sending a fax by Direct Keypad Dialling Redial Automatic redialling Broadcasting sending a fax to multiple destinations Sending a Fax From MemoryEmpfang to set Memory transmission If the memory becomes full Receiving Faxes Using TEL/FAX ModePseudo Ring Duration for Tel/Fax Mode Empfang until the arrow Press once and 3 times Using A.M. ModeEnter a number as follows for the desired duration Changing the number of rings Using FAX ModePress Funktion once and once Enter the desired number of rings any Using TEL ModeNumber from 2 to Answering with the fax’s handset Replace the handset Phone goes dead Optional Reception Settings Fax Signal Receive To turn it off Changing the number for remote fax activationPress To turn on the function, or Enter the desired number any number from 0 to Example 3 Press To select AUTO, or 2 to Reception RatioSelect 100% Substitute Reception to Memory Making Copies Load the documents face down. Maximum of 10 pages Copy Cut-off Changing the outgoing message Answering Machine ConnectionPreparations Comments Set the reception mode to A.M Using the Answering Machine ConnectionSet your answering machine to auto answer How answering machine mode operates Optional A.M. Mode SettingsQuiet Detect Time Quiet Time On A.M. Failure Quiet Detect Start Time Quiet Start Press YES to turn on Caller ID Caller ID Requires Subscription to ServiceSpecial Functions To turn off Caller ID, press How Caller ID operates Display messages Press Twice Press Stop when you have finished viewing the listViewing the Caller ID list Dialling and transmission begin Fax Priority Call To delete calls from the Caller ID listPress Speicher to store or clear the number Blocking voice calls Press Funktion once and twice Blocking Reception of Unwanted FaxesPress once and twice Polling Requesting a Fax Transmission Press Abruf Making enquiry calls PBX operationsTransferring calls Telephone Number List Setup ListPrinting Lists Caller-ID List Transaction Report Headings in Transaction Report Transaction Report print condition Help List Maintenance Print head Maintenance Scanning glass and rollers Housing If the scanning glass is difficult to clean Line error TroubleshootingProblems and Solutions Problem Solution Dialling and transmission problems Correct socket. See Connecting the handset on Reception and copying problems Answering machine connection General problems See Loading the Imaging Film on Messages and Signals Press Start KEY Substitute Reception to Memory on page 48. If you Audible signals Recalling Clearing Paper Jams Clearing a jammed document Clearing jammed printing paper Quick Reference Guide Sending Faxes Index Index Page Sharp Electronics Europe Gmbh