Assembly
Prior to Assembly
Before assembling this unit, make sure you have all the components required for a complete unit:
GP3410
Spark plug wrench
Spanner
3mm Hex Wrench
4mm Hex Wrench
Parts bag including:
●1.0" hose clamps (3 each)
●hose fittings and gaskets (2 each)
●strainer
Install the Suction and Discharge Hoses
CAUTION! |
|
| Priming Port |
| ||
This pump is intended for pumping |
|
| Discharge Port | |||
|
|
|
| |||
fresh water only. |
|
|
|
|
| |
Ingested debris can damage the |
|
| Gasket |
|
| |
pump impeller and seals. |
| Ring Nut | Suction Port |
|
| |
Never operate the pump if the |
|
|
|
| ||
|
|
|
|
| ||
strainer is missing or damaged. |
| Hose Clamp |
|
|
| |
. Assemble a barbed hose fitting, ring |
|
|
|
|
| |
nut, and gasket as shown, and thread |
|
|
|
|
| |
the completed hose fitting assembly |
|
| Barbed Hose |
|
| |
onto the pump suction port. Assemble |
|
| Fitting |
|
| |
the remaining hose fitting to the pump |
|
|
|
|
| |
discharge port. |
|
|
|
|
| |
. Push a 1.0" suction hose (not provided) |
| Suction |
|
|
| |
over the suction hose fitting on the pump |
|
|
|
| ||
| Hose |
|
|
| ||
body, and secure with a 1.0" hose clamp as |
|
| Hose Clamp |
| Suction | |
shown. Working at the opposite end of the | Figure 1B |
|
| Strainer | ||
suction hose, use a second 1.0" hose clamp |
|
|
| |||
|
|
|
|
| ||
to install and secure the suction strainer. | 4. | Install the discharge hose (not pro- |
| IMPORTANT! | ||
3. Submerge the suction hose strainer in |
| |||||
| vided) and secure with the remaining | Place the pump as close to the water | ||||
the water source. For maximum per- |
| 1.0" hose clamp. |
| |||
|
| source as possible. Increases in suction | ||||
formance, avoid placing the strainer | 5. | Recheck that both the suction and dis- | ||||
lift will lower pump performance. Do not | ||||||
directly in heavy accumulations of | ||||||
| charge hoses are free from obstruc- | exceed maximum suction head of 26 feet. | ||||
leaves, silt, or other debris. |
| |||||
| tions, and that all connections are |
|
| |||
|
|
|
| |||
tightly secured.
Priming
Before the pump can develop suction or “lift” at the water source, the pump impeller must first be primed by filling the pump housing with water. Once the GP3410 has been primed, additional prim- ing should be required only if the pump has been drained or otherwise emptied.
. Remove the filler plug at the top of the pump housing. Use care not to lose the sealing ring beneath the filler plug.
IMPORTANT!
A damaged or missing filler plug seal may allow air to leak into the pump housing. Air leakage can lower performance!
. Fill the pump housing through the priming port (Figure 2) with clean water until water overflows from the filler plug hole on the pump body.
3.Replace and securely tighten the filler plug.
CAUTION!
Never allow the pump to run dry! Operation without water can perma- nently damage the pump seals.
Filler Plug
Sealing ring
Priming port
Figure 2
