Manuals / Brands / Computer Equipment / Switch / Siemens / Computer Equipment / Switch

Siemens Electrical Lean Switch Windows NT DLC Protocol Installation

1 97

Download 97 pages, 1.14 Mb

Diagnostics over Industrial Ethernet

Industrial Ethernet

A5E00152007-03 49

4. Once you have selected the language, the menu shown in Figure 6-2 opens.

Select a network adapter with Settings -> Network Adapter.

All the network interfaces (maximum of four) found in your system will be listed.

Select the network adapter you require by clicking on it. Make sure that you

read the information in the "readme" file on the supplied CD.

Figure 6-2Configuring the Network Adapter

Note

If the network adapter installed in your system is not displayed, the DLC protocol

required for the network adapter is not installed. In this case, follow the steps

outlined below to install the DLC protocol:

Windows NT – DLC Protocol Installation

● Select Start -> Settings -> Control Panel.

● Click on the "Network" icon.

● Go to the "Protocols" tab and click the "Add" button.

● From the network protocols displayed, select the DLC Protocol.

● Confirm your selection with "OK".

Note

Make sure you have your Windows CD at hand. You may need to reinstall

Windows service packs.

Contents

Main SIMATIC NET Industrial Ethernet Electrical Lean Switch Classification of Safety-Related Notices ! Trademarks Safety Instructions Regarding your Product Qualified Personnel Correct Usage of Hardware Products Preface Further Documentation Finding Information Guide to the Manual Audience Personnel Qualification Requirements Standards and Approvals Contents Page Page 1.1 ELS TP40 Page 1.2 ELS TP40M Page 1.3 ELS TP80 Page Page Page Page Page Page Page 4.1 Ports and Displays of the ELS TP40 4.1.1 TP Ports Page 4.1.2 Power Supply Page 4.1.3 Displays Power display (green LED) Port status display (green/yellow LEDs) 4.2 Ports and Displays of the ELS TP40M 4.2.1 TP Ports Page 4.2.2 Power Supply Page 4.2.3 Displays Power Display (green and red LEDs) Port Status Display (green/yellow LEDs) Port Status Display During Startup 4.3 Ports and Displays of the ELS TP80 4.3.1 TP Ports 4.3.2 Power Supply 4.3.3 Displays Power display (green LED) Port status display (green/yellow LEDs) Page 5.1 Consignment Unpacking, Checking the Consignment 5.2 Installation| Preparations DIN Rail Mounting Page Page Installation in a 19" Cubicle Wall Mounting Grounding Connecting the IE FC TP Cable to the ELS TP40 or ELS TP40M Page Page Page 6.1 Introduction 6.2 Configuration 6.2.1 Automatic IP Address Assignment using DHCP (Factory Setting) 6.2.2 Manual IP Address Assignment Primary Setup Tool (PST) Installation of the Primary Setup Tool Page Windows NT DLC Protocol Installation Windows 2000 DLC Protocol Installation Windows XP DLC Protocol Installation User Interface of the PST Changing the Language Package Changing the Network Adapter Configuration Configuring the ELS Page Page Page 6.3 Web Based Management (WBM) 6.3.1 General 6.3.2 Requirements 6.3.3 Access using WBM How to Access WBM on the ELS 6.3.4 User Interface of the WBM 6.3.5 Management Menus 6.3.6 Switch Information Page 6.3.7 IP Address Information Page 6.3.8 E-Mail Configuration Page 6.3.9 Trap Configuration Construction of the Trap report LED-Status: Port Status: 6.3.10 Event Configuration 6.3.11 Statistic Information 6.4 Diagnostics Using SNMP ELS private MIB 6.5 Internet Browser Settings 6.5.1 Microsoft Internet Explorer 5.5 or 6.0 Page Page Page Page 6.5.2 Netscape 6.1 or 6.2 Page Page 7.1 Technical Specifications of the ELS TP40 Page Page 7.2 Technical Specifications of the ELS TP40M Page Page 7.3 Technical Specifications of the ELS TP80 Page 8 Further Support 8 Who to Contact Automation and Drives, Service & Support Service & Support on the Internet Training for SIMATIC NET Certification 9 Notes on the CE Mark 9 Installation Guidelines Conformity Certificates Notes for the Manufacturers of Machines 10 Glossary 10 11 Index Page 12 References 12