B89, 250B, Changing the system code | Siemens Gigaset 2010 manual

14.8.98

KAP04.FM5

Gigaset 2010, UEB/engl.: A30852-X1100-E301-2-7619

Operating modes

Changing the system code

B#8* Start setting procedure.

Enter the current system code (factory default "0000").

o

Enter the new four-digit system code. Note carefully the

o

number entered.

oEnter the new system code again to confirm.

BStore the setting.

Changing the handset PIN

B89

Start setting procedure.

Enter the current PIN (factory default "0000").

o

Enter the new four-digit PIN. Note carefully the number

o

entered.

oEnter the new PIN again to confirm.

BStore the setting.

Resetting the base station to factory defaults

You can use this procedure to reset the following settings to factory defaults:

●Signaling method (DTMF/flash 300 ms) ➔ page 16

●Pause length following exchange code ( 3 seconds) ➔ page 19

●Call allocation (collective call) ➔ page 51

The following stored data can be deleted:

●Exchange code

The stored system code (➔ page 19) is not de- leted.

All registered handsets remain registered.

B#1

o

O250B

Start setting procedure.

Enter the four-digit system code (factory default: “0000“) (➔ page 19).

Reset the base station to the factory default.

20

Image 30

Siemens Gigaset 2010 B89, Resetting the base station to factory defaults, 250B, Changing the system code

Contents

Gigaset Gigaset Wegweiser Overview Gigaset Overview Keys Keys on the base stationKeys on the Gigaset 1000S mobile unit Overview Key functions and display symbols Display Symbols top lineDisplay symbols bottom line Overview Meaning of symbols Safety precautions Certification and CE marking Contents Contents Stepwise startup Observe the safety precautionsCheck the contents of the package Stepwise startup Stepwise startup Connecting the base station Power cordPhone cord Stepwise startup Inserting the batteries into the handset Charging the batteries Stepwise startup Check signaling method Checking your own telephone’s signalling methodSetting the phone to dial pulsing DP Installing the base station Installation site/installation areaTemperature/ambient conditions For users who wear hearing aids NiMH rechargeable Batteries 1100 mAh Maintenance notes Connecting the telephone socketMounting the carrying clip onto the handset Technical data Gfsk Warranty Third party use/disposal Procedure in the case of malfunctions Symptom Cause Remedy With telephone systems Exchange code not entered Overview Signal tones Operating modes Switching the handset to protected modeOperating modes ON/OFF/PROTECTED modes When the handset is switched off Switching on the handset Operating modes Signaling method Checking the signaling method of your telephone lineSetting the signaling method Possible signaling method settings Operating modes Operating in a telephone systemO037 B Operating modes Exchange codes Entering the exchange code Modify the pause length according to the excharge code 024B 025B 020B 021BChanging the system code, changing the PIN Deleting the exchange code 250B Resetting the base station to factory defaultsB89 Changing the system code KAP04.FM5 Accepting calls Incoming callsIncoming calls If the handset is in the charging unit Switching off the microphone mute function Ending an internal callBR or Calling external subscribers External outgoing callsExternal outgoing calls FN b F Manually inserting a pause No answer or line busy External outgoing callsRedial Repeating the last number dialed Dialing speed dial numbers Dialing with speed dial numbers and number check Dialing a DSS number from a locked handset Ending a call FN b G Collective ringing and internal callsCollective ringing and internal calls End call prematurelyn Disconnect internal party again Internal consultation calls and transferring calls Internal consultation calls and transferring callsConsultation calls Either Base station settings Base station settingsFN b Base station settings Setting the base station ringer tone Switching music-on-hold on/off Setting the ringer volume Individual settings on the Gigaset 2000S mobile unitIndividual settings on the Gigaset 2000S mobile unit Setting the ringer tone B31 VolumeActivating/deactivating notification and warning tones Activating/deactivating the key confirmation tone B32 B34B37 B33 B35 Activating/deactivating automatic call acceptance B38Activating/deactivating the synchronization tone Checking or store speed dial numbers Clearing all speed dial numbers Activating/deactivating the call duration display Activating/deactivating the call duration displayO96 Gigaset 2010 lock functions Emergency calls when the Gigaset 2010 is locked1B Switch on the lock. or 0B Switch off the lock Gigaset 2010 lock functions #25 Displaying and storing emergency numbersDeleting all emergency numbers Gigaset 2010 lock functions Barred numbers for handsets FN bDisplaying or storing barred numbers Activating/deactivating the call number lock Deleting all barred numbers Set Unrestricted trunk access Activating/deactivating the handset lock B81 B80 Lock functions on the handsetLock functions on the handset DSS number for handset lock Display or store a DSS number Deleting a DSS number Display with system lock B F HDisplay with locked handset Display with call number lock Registering a Gigaset 2000S handset at a base station Prepare the base stationRegister the handset De-registering a handset from a base station Operating more than one handset Switching between collective ringing and ring priorityOperating more than one handset Ring priority for incoming calls Setting the number of rings for ring priority Selecting a handset for ring priority Procedure for operating at more than one base station Operation at more than one base stationOperation at more than one base station Setting the preferred station Selecting the best station PfN With Gigaset 2000S handset You can reset the handset to the factory default Quick reference guide handset Gigaset 2000S Quick reference guide handset Gigaset 2000S Index Index GIGA2010.SIX Ringer KAP21.FM5