Installing the base station | Siemens Gigaset 2010 manual

18.11.98

Kap03.fm5

Gigaset 2010, UEB/engl.: A30852-X1100-E301-3-7619

Notes on operation

Notes on operation

Installing the base station

Installation site/installation area

●A 220/230V power socket must be located at the in- stallation site.

●In order to avoid interference, the base station should not be in the direct vicinity of other electronic equip- ment such as HiFi, office or microwave equipment.

●Place the base station on a level, non-slip surface. The device feet do not normally leave any unsightly marks. However, due to the variety of varnishes and polish used on furniture, the possibility of marks cannot be entirely ruled out.

●Radio transmission between the base station and handsets complies with the DECT standard. Gigaset 2010 thus observes all relevant regulations. However, if there is interference to the picture or sound of your satellite equipment, consult your specialist satellite dealer.

●Depending on ambient conditions, the maximum ra- dio range between the base station and the handset is approx. 300 m outdoors, and approx. 50 m indoors. If the range warning is activated for the handset

(➔ page 36), a signal will sound when you move out- side the radio range.

Temperature/ambient conditions

●The base station is designed for operation in protect- ed areas with a temperature range from +5 °C to +45° C.

●The base station should not be installed in damp ar- eas (such as bathrooms or laundry rooms), or close to heat sources, or in direct sunlight.

5

Image 15

Siemens Gigaset 2010 Installing the base station, Installation site/installation area, Temperature/ambient conditions

Contents

Gigaset Wegweiser Gigaset Overview Gigaset Overview Keys Keys on the base stationKeys on the Gigaset 1000S mobile unit Overview Key functions and display symbols Display Symbols top lineDisplay symbols bottom line Overview Meaning of symbols Safety precautions Certification and CE marking Contents Contents Stepwise startup Observe the safety precautionsCheck the contents of the package Stepwise startup Stepwise startup Connecting the base station Power cordPhone cord Charging the batteries Stepwise startup Inserting the batteries into the handset Stepwise startup Check signaling method Checking your own telephone’s signalling methodSetting the phone to dial pulsing DP Installing the base station Installation site/installation areaTemperature/ambient conditions For users who wear hearing aids NiMH rechargeable Batteries 1100 mAh Maintenance notes Connecting the telephone socketMounting the carrying clip onto the handset Gfsk Technical data Third party use/disposal Warranty Symptom Cause Remedy Procedure in the case of malfunctions With telephone systems Exchange code not entered Overview Signal tones ON/OFF/PROTECTED modes Switching the handset to protected modeOperating modes Operating modes Switching on the handset When the handset is switched off Operating modes Signaling method Checking the signaling method of your telephone lineSetting the signaling method Possible signaling method settings Operating modes Operating in a telephone systemO037 B Entering the exchange code Operating modes Exchange codes Deleting the exchange code 024B 025B 020B 021BChanging the system code, changing the PIN Modify the pause length according to the excharge code Changing the system code Resetting the base station to factory defaultsB89 250B KAP04.FM5 If the handset is in the charging unit Incoming callsIncoming calls Accepting calls Switching off the microphone mute function Ending an internal callBR or FN b F External outgoing callsExternal outgoing calls Calling external subscribers Repeating the last number dialed No answer or line busy External outgoing callsRedial Manually inserting a pause Dialing with speed dial numbers and number check Dialing speed dial numbers Ending a call Dialing a DSS number from a locked handset End call prematurelyn Collective ringing and internal callsCollective ringing and internal calls FN b G Disconnect internal party again Internal consultation calls and transferring calls Internal consultation calls and transferring callsConsultation calls Either Base station settings Base station settingsFN b Switching music-on-hold on/off Base station settings Setting the base station ringer tone Setting the ringer tone Individual settings on the Gigaset 2000S mobile unitIndividual settings on the Gigaset 2000S mobile unit Setting the ringer volume Activating/deactivating the key confirmation tone VolumeActivating/deactivating notification and warning tones B31 B33 B34B37 B32 B35 Activating/deactivating automatic call acceptance B38Activating/deactivating the synchronization tone Checking or store speed dial numbers Clearing all speed dial numbers Activating/deactivating the call duration display Activating/deactivating the call duration displayO96 Gigaset 2010 lock functions Emergency calls when the Gigaset 2010 is locked1B Switch on the lock. or 0B Switch off the lock Gigaset 2010 lock functions #25 Displaying and storing emergency numbersDeleting all emergency numbers Gigaset 2010 lock functions Barred numbers for handsets FN bDisplaying or storing barred numbers Deleting all barred numbers Activating/deactivating the call number lock Set Unrestricted trunk access DSS number for handset lock Lock functions on the handsetLock functions on the handset Activating/deactivating the handset lock B81 B80 Deleting a DSS number Display or store a DSS number Display with call number lock B F HDisplay with locked handset Display with system lock Registering a Gigaset 2000S handset at a base station Prepare the base stationRegister the handset De-registering a handset from a base station Ring priority for incoming calls Switching between collective ringing and ring priorityOperating more than one handset Operating more than one handset Selecting a handset for ring priority Setting the number of rings for ring priority Procedure for operating at more than one base station Operation at more than one base stationOperation at more than one base station Selecting the best station Setting the preferred station With Gigaset 2000S handset PfN You can reset the handset to the factory default Quick reference guide handset Gigaset 2000S Quick reference guide handset Gigaset 2000S Index Index GIGA2010.SIX Ringer KAP21.FM5