User’s Guide | Silex technology SX-200 guide

User’s Guide

3.Connect the print server to your printer(s) using the USB and/or parallel port of your printer. For a USB connection, use a standard USB A (print server side) to B (printer side) cable. For a parallel connection, use an IEEE 1284-compliant parallel printer cable.

4.Plug the print server power supply adapter into a suitable AC receptacle, and then plug the power supply cable into the print server. The print server will run through a sequence of power-up diagnostics for a few seconds.

If the print server is operating properly, the power LED will illuminate continuously (refer to page 1-5 for detailed LED status descriptions).

If the power LED blinks continuously in a regular pattern, a problem exists. If this is the case, try powering the print server OFF and then ON again.

If the problem persists, refer to the Troubleshooting section in this User’s Guide.

5.Connect the print server to your network through a switch or hub using a category 5 (CAT5) Ethernet cable. The print server’s IP address must be configured before a network connection is available. If your network offers DHCP (Dynamic Host Configuration Protocol), the print server will automatically search for a DCHP server upon power up and obtain an IP address. If your network does not offer DHCP, a static (fixed) IP address must be assigned (see your system administrator for assistance). In most cases, a fixed IP address is preferred because a DHCP server may not always assign the same IP address to the print server when the print server is powered ON.

NOTE: The IP address must be within a valid range, unique to your network, and in the same subnet as your PC.

NOTE: For wireless print servers, if a wired connection is established to the unit, the wireless link will be disabled.

Document #40181-420 Rev. A

14

Image 14

Silex technology SX-200 user manual User’s Guide

Contents

SX-200 User’s Guide SET NW AUTHtype SET NW CHannel User’s Guide SET Port U1 Nbuf ENable DIsable SET Power Window nnnn SH POP3 SH Smtp Introduction Package Contents Product Overview Other Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators Label Color State Status Wireless Default Settings wireless print servers only Factory Default SettingsDefault Settings wired and wireless print servers Pushbutton Functions Hardware Installation Before You Begin User’s Guide User’s Guide Verifying the Connection to the Printer ExtendView Utility Configuration and ManagementConfiguration Options Web Browser Interface HP Web JetAdmin Utility Configuration Console Document #40181-420 Rev. a User’s Guide Telnet User’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration Configuring to Print Using TCP/IP OS Introduction TroubleshootingPrinting Problems Troubleshooting Windows Problems Checking the Network Connection and Cabling User’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Where to Get Help User’s Guide Returning Products Appendix a Safety and Regulatory Notices Information for United States Users User’s Guide Declaration of Conformity FCC Information for Canadian Users IC notice User’s Guide Information for European Users Declaration of Conformity CE Appendix B Updating Firmware User’s Guide User’s Guide Loading New Firmware Macintosh OS-X Telnet Command Console Access Command console access informationNetwork Commands Serial Port Command Console Access SH NW ENC SH NW AuthSET NW ENC SET NW KEY# SH NW Speed SH NW ModeSET NW Keyval SET NW Apden SET NW RTSSH NW RTS SH NW Apden SH NW Certcn SH NW StatsSET NW Certcn SET NW CERTCN2 SH NW Certexp SH NW CERTCN2SET NW Certexp SET NW Certkey SH NW Inap SET NW PWSET NW Inap SET NW Realm SH NW Wpagroup SH NW WpaautoSET NW Wpagroup SET NW Wpapsk SH NW DFS SH NW Iroam NW IroamSET NW DFS SET NW REGDOMain Serial Port Commands Port CommandsSET NW Wired SH NW REGDOMain Set serial port parity to NONE, EVEN, ODD, MARK, or Space SET Port S1 SPeedSet serial port flow control to NONE, XON/XOFF, CTS, or DSR Sets the data bits on the serial port SET Port P1 BIDir User’s Guide Parallel Port CommandsEnable or disable bidirectional mode Shows Port parameters Sample output CL Port port JOB SET Port P1 Nbuf ENable DIsableEnable or disable PJL status initialization SET SERVEr DEscription Server Information CommandsUSB Port Commands SET SERVEr NAme SH Serial SET Snmp SETCOMM1SET Snmp SETCOMM2 SH Snmp SH SERVErSH SERVEr CO SH VErsion Service Commands SET Servi service name NAme SET Servi service name FRSSET Servi service name IP SET Servi service name POrt String Commands User’s Guide SH STRing stringnum TCP/IP CommandsSET IP ACcess SH FILters SET IP Chksum SET IP LPD SET IP FTPSET IP Http SET IP TCP SET IP Tftp Power Configuration Commands SH IP User’s Guide Firmware Update Shows the firmware update parameters Sample output User’s Guide SH LOAd Exit Other CommandsSET Default SH Free Save SET PoweronSH Poweron Netware Commands Unprotect SET Netw SErver SET Netw QServerSET Netw REscan CL Netw SErver Email Printing Commands SET Smtp ENable SET POP3 PAsswordSET POP3 TImeout SET Smtp ADdress SH Smtp DLC / Netbeui CommandsSH POP3 SH DLC Appletalk Commands Wireless Security Configuration ExtendView Key Selection SH NW SET NW KEY# SET NW RTS SH NW Apden SH NW CERTCN2 SET NW Inap SH NW Wpagroup