Manuals / Silex technology / Computer Equipment / Network Card

Silex technology SX-200 User’s Guide About This User’s Guide, Windows System Requirements

Models: SX-200

1 80

Download 80 pages 35.55 Kb

Page 8

User’s Guide

About This User’s Guide

This User’s Guide contains information on system requirements, basic troubleshooting, and instructions on the following:

Installing the print server hardware

Configuring the print server for use on your network

Windows print queue configuration

Macintosh print queue configuration

Windows™ System Requirements

To configure the print server settings (wired and wireless versions) using the provided ExtendView Utility in Windows, your Windows-based system should include the following components:

A PC with a 133 MHz or higher processor

Microsoft Windows operating system

At least 64 MB of RAM (memory)

At least 3 MB of free hard disk space to install the software

A CD-ROM drive (to load the software)

A PC equipped with a USB version 1.1 or 2.0 port

An Internet connection (for online product registration)

Other Operating System Requirements

Users can access the configuration settings for the Serial Server through a standard web browser by entering the IP address the serial server obtains from a DHCP server. If your network does not have DHCP service, then enter the default static IP address of the Serial Server (192.0.0.192).

Document #40181-420 Rev. A

8

Image 8

Silex technology SX-200 user manual User’s Guide About This User’s Guide, Windows System Requirements

Contents

User’s Guide SX-200User’s Manual Document #40181-420 Rev. AUser’s Guide User’s Guide Document #40181-420 Rev. ADocument #40181-420 Rev. A SET PORT U1 NBUF ENable DIsableUser’s Guide Document #40181-420 Rev. A SET POWER WINDOW nnnnUser’s Guide User’s Guide Document #40181-420 Rev. AIntroduction Package ContentsSection 1 - Product Overview Other Operating System Requirements User’s Guide About This User’s GuideWindows System Requirements User’s Guide Wireless Print Server Requirements User’s Guide Print Server Components LED Indicators LabelColor StateFactory Default Settings Default Settings wired and wireless print serversSetting Wireless Default Settings wireless print servers onlyUser’s Guide Section 2 - Hardware InstallationBefore You Begin 3. Connect the print server to your printers using the USB and/or parallel port of your printer. For a USB connection, use a standard USB A print server side to B printer side cable. For a parallel connection, use an IEEE 1284-compliant parallel printer cable User’s GuideUser’s Guide Verifying the Connection to the Printer Section 3 - Configuration and Management Configuration OptionsExtendView Utility Web Browser InterfaceUser’s Guide HP Web JetAdmin UtilityConfiguration Console User’s Guide Configuring the Print Server via an Ethernet Connection User’s Guide User’s Guide telnetUser’s Guide Windows Print Queue Configuration Macintosh Print Queue Configuration User’s Guide Configuring to Print Using TCP/IP OSMACINTOSH CONFIGURATION OS Section 4 - Troubleshooting Printing ProblemsChecking the Interface between the Print Server and the Printer User’s GuideUser’s Guide Troubleshooting Windows ProblemsChecking the Network Connection and Cabling User’s Guide Troubleshooting Network Configuration Problems User’s Guide Troubleshooting Wireless Configuration Problems Section 5 - Where to Get Help User’s GuideUser’s Guide Returning Products User’s Guide Appendix A - Safety and Regulatory NoticesInformation for United States Users User’s Guide Declaration of Conformity FCC Information for Canadian Users IC noticeUser’s Guide Information for European Users Declaration of Conformity CEUser’s Guide Appendix B - Updating FirmwareLoading New Firmware Using the TCP/IP Update Utility User’s Guide 3. Verify that the files are correct, and then click on OK. The utility will start searching for qualified print servers present on the networkUser’s Guide Document #40182-420 Rev. AUser’s Guide Loading New Firmware Macintosh OS-X2. Go to the terminal command prompt and type cd desktop Command console access information Network CommandsTelnet Command Console Access Serial Port Command Console AccessSET NW AUTHtype SH NW AUTHSET NW CHannel SET NW ENCUser’s Guide SET NW KEYVAL SET NW MOdeSET NW RAdio SH NW MODECL NW SSid SET NW BSsidCL NW BSsid SET NW RTSSH NW STATS SET NW CERTCNSH NW CERTCN SET NW CERTCN2SH NW CERTCN2 SET NW CERTEXPSH NW CERTEXP SET NW CERTKEYShows the selected inner authentication mode SET NW PWSET NW INAP SH NW INAPSH NW WPAAUTO SET NW WPAGROUPSH NW WPAGROUP SET NW WPAPSKSH NW IROAM NW IROAM SET NW DFSSH NW DFS SET NW REGDOMainPort Commands SET NW WIREDSerial Port Commands SH NW REGDOMainSET PORT CLEAR PORT S1 JOBSET PORT S1 FLOW SET PORT S1 PARITYUser’s Guide Parallel Port Commands SET PORT P1 ACKHSET PORT P1 BIDir SET PORT P1 ECPSET PORT P1 NBUF ENable DIsable SET PORT P1 NOINBUSYSET PORT P1 POLL SET PORT P1 PSTAServer Information Commands USB Port CommandsSET PORT U1 NBUF ENable DIsable SET SERVEr DEscriptionSET SNMP JETADmin SET SNMP SETCOMM1SET SNMP SETCOMM2 SET SNMP CONtactSH SERVEr SH SERVEr COSH SNMP SH VErsionService Commands SET SERVI service name BOTSET SERVI service name EOT SET SERVI service name FIlterSET SERVI service name FRS SET SERVI service name IPSET SERVI service name NAme SET SERVI service name POrtString Commands User’s Guide SET SERVI service name RECeiveSET SERVI service name TCP SET SERVI service name QUEUETCP/IP Commands SET IP ACcessUser’s Guide SH STRing stringnum SH FILtersUser’s Guide SH IP ACcess SET IP ARP ENableSET IP BOot SET IP ENableUser’s Guide SET IP FTIme SET IP FTPSET IP HTTP SET IP KEepaliveSET IP RARp SET IP REtrySET IP ROuter SET IP SUbnetPower Configuration Commands SET IP TImeoutSET POWER DELAY nnnn SET POWER PERIOD nnnnThis is the time, in milliseconds, the radio stays awake each time it wakes up in power save mode i.e., every PERIOD msec the radio wakes up for WINDOW msec to see if there is traffic for it. The value is in the range User’s GuideFirmware Update SET LOAd ENableSET LOAd HOst SET LOAd IPDocument #40182-420 Rev. A User’s Guide SH LOAdShows the firmware update parameters sample output Other Commands SET DEFAULTHElp command EXITSET PAssword SET POWERONSH POWERON SET PROTectNetware Commands SET NETW ENableSET NETW PAssword User’s Guide UNPROTECTSET NETW QServer SET NETW REscanSET NETW SErver CL NETW SErverEmail Printing Commands SET POP3 ENableUser’s Guide SH NETWare SET POP3 ADdressSET POP3 PAssword SET POP3 TImeoutSET SMTP ENable SET SMTP ADdressDLC / NETBEUI Commands SET DLC ENableSET DLC TIMeout User’s Guide SH POP3Appletalk Commands User’s Guide SET NetBEUI ENableSET NETBIOS DOMain SET NETBIOS MEthodWireless Security Configuration Web Browser Interface and ExtendView Security ConfigurationUser’s Guide ExtendViewAuthentication Type PasswordAuthentication Protocol User’s GuideCommand Line Console Configuration User’s GuideWPA Auto Associate WPA Group KeyUser’s Guide SET NW ENCSET NW KEY# SET NW KEYVALUser’s Guide SH NW SPEEDSET NW SSid CL NW SSidUser’s Guide SH NW APDENSH NW STATS SET NW CERTCNUser’s Guide SH NW CERTCN2SET NW CERTEXP SH NW CERTEXPUser’s Guide SET NW INAPSH NW INAP SET NW REALMUser’s Guide SH NW WPAGROUPSET NW WPAPSK SET NW WPATRACE