Indication

Meaning

 

 

AUDIO 48kHz?

At back space editing, you are

 

switching from 32 kHz audio recording

 

mode (4-channel mode) to 48 kHz

 

audio recording mode (2-channel

 

mode).

 

 

AUDIO 32kHz?

At back space editing, you are

 

switching from 48 kHz audio recording

 

mode (2-channel mode) to 32 kHz

 

audio recording mode (4-channel

 

mode).

 

 

ERROR:91-13F

Failure in loading or saving the

 

cassette memory data.

 

 

CLIP CONT?

Asking whether you will continue

 

shooting in ClipLink mode or not when

 

the cassette contains ClipLink data.

 

(The indication disappears when you

 

press the ClipLink CONTINUE button

 

or start the next shooting without

 

pressing it.)

 

 

CLIP NEAR END

At ClipLink shooting, capacity for only

 

1 to 3 clips remains.

 

 

CLIP END

Impossible to record any more clip

 

shots.

Note

If the message appears other than above, contact your Sony dealer.

qd External VCR (connected to the VTR/CCU connector (26-pin) or DV OUT connector) status indication (when an external VCR is connected)

Shows the external VCR operation status.

Notes

•When the VTR TRIGGER switch is set to INT ONLY, operation status is not shown for an external VCR connected to the DV OUT connector, even if that VCR starts recording.

•When there are external VCRs connected to both the VTR/CCU and DV OUT connectors, REC2 is displayed when either VCR starts recording.

•When iLINK CTL on page 3 of the advanced menu is set to OFF, the status of an external VCR connected to the DV OUT connector is not displayed.

•Depending on the type of external VCR connected to the DV OUT connector, status may not be displayed.

qf VCR recording mode indication (when an external VCR is connected to the VTR connector (26-pin) or DV OUT connector)

Shows recording mode of the internal and external VCRs set by the VTR TRIGGER switch.

Indication

Meaning

 

 

PARA

Simultaneous recording of the internal

 

and external VCRs

 

 

INT

Recording on the internal VCR

 

 

EXT

Recording on the external VCR

 

 

Note

Even if there is an external VCR connected to the DV OUT connector, the above indications do not appear if iLINK CTL on page 3 of the advanced menu is set to OFF.

qg White balance indication The following indications appear.

Indication

Meaning

 

 

EZ

Operating in EZ mode (The ATW function is

 

selected.)

 

 

ATW

The ATW function is selected (The ATW

 

button was pressed and the indication is lit.)

 

 

W:A

White balance memory A is selected.

 

 

W:B

White balance memory B is selected.

 

 

W:P

Preset white balance is selected.

 

 

W:M

Manual adjustment is performed remotely.

 

 

qh SKIN DTL indication

This appears when the skin detail function is activated (The SKIN DTL switch is set ON.)

qj EVS indication

This appears when the EVS (Enhanced Vertical definition System) function is enabled. (See page 130.)

qk Lens f-stop indication

This shows the f-stop of the lens.

Note

Depending on the lens being used, this indication may differ slightly from the actual f-stop on the lens.

ql Gain indication

This shows the gain value, and the settings of the HYPER GAIN switch (see page 100) and the DPR (Dual Pixel Readout) function as shown in the following table.

Menus and Indications Screen Viewfinder 4 Chapter

Chapter 4 Viewfinder Screen Indications and Menus 89