OPERATIONAL FUNCTION [Operational]: Operation

 

Description of settings

 

 

 

 

 

 

settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEARCH ENABLE [>Search ENA]: Select how the unit enters

 

*DIAL DIRECT [>> DIAL]: Press the SEARCH button or,

the search mode.

 

 

 

except during editing, turn the search dial.

 

 

 

 

VIA SEARCH KEY [>> via KEY]: Press the SEARCH button.

 

 

 

 

 

 

 

 

 

 

 

 

 

MAX SRCH SPEED [>Max

SHUTTLE [>>SHUTTLE]:

 

X60 [>>> X60]: Maximum 60 times normal speed

SRCH]: Specify the

Specify the maximum

 

*X32 [>>> X32]: Maximum 32 times normal speed

maximum tape speed in

tape speed in search

 

X16 [>>> X16]: Maximum 16 times normal speed

search mode (shuttle) and

mode (shuttle).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F.FWD (fast forward)/REW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F.FWD/REW [>>F.FWD/

 

MAX [>>> MAX]: No maximum tape speed is specified.

(rewind) mode.

 

REW]: Specify the

 

*X85 [>>> X85]: Maximum 85 times normal speed

 

 

 

maximum tape speed

 

X60 [>>> X60]: Maximum 60 times normal speed

 

in F.FWD/REW mode.

 

X32 [>>> X32]: Maximum 32 times normal speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When this item is set to MAX, the playback video signal is

 

 

 

muted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JOG RESPONSE [>JOG dial]: Select the tape speed

 

*TYPE1 (–1 to +1) [>> type 1]: Tape speed varies linearly

characteristics for the search dial rotation rate in jog mode.

 

 

over the range −1 to +1.

 

 

 

 

 

 

 

 

 

TYPE2 (–3 to +3) [>> type 2]: Tape speed varies stepwise as

 

 

 

 

shown in the figure below over the range −3 to +3.

 

 

 

 

(Characterized by a zone around −1 and +1 where the

 

 

 

 

tape speed is independent of the rotation rate)

 

 

 

TYPE3 (–3 to +3) [>> type 3]: Tape speed varies linearly over

 

 

 

 

the range −3 to +3, as shown in the figure below.

 

 

 

 

 

 

 

 

 

 

 

 

TYPE2

 

 

TYPE3

 

 

 

 

 

 

 

 

 

 

 

 

Speed

 

 

 

 

 

Speed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+3

 

FWD

 

 

+3

 

FWD

Rotation rate

 

 

 

 

 

 

 

 

 

 

 

 

 

+1

 

 

Rotation rate

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RVS

 

 

 

 

-1

FWD

 

RVS

 

 

FWD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RVS

 

-3

 

 

 

 

-3

 

 

 

 

 

 

 

 

 

RVS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PREROLL TIME [> Preroll]: Set the preroll time.

 

0 SEC [>> 0 sec] to 15 SEC [>> 15 sec]: The preroll time

 

 

 

 

can be set in one-second increments to between 0 and 15

 

 

 

 

seconds.

 

 

 

 

 

 

 

 

 

 

A preroll time of at least 5 seconds is recommended when

 

 

 

using this unit for editing. When an editing control unit such as

 

 

 

the PVE-500 has been connected, this setting is disabled and

 

 

 

the setting on the editing control unit is in effect. Operations

 

 

 

such as the preroll time setting and the time data switching

 

 

 

operation are also performed on the editing control unit.

 

 

 

Factory default setting: 5 SEC [>> 5 sec]

 

 

 

 

 

 

 

 

 

 

 

 

 

AFTER CUE-UP [> After CUE]: Select the operating mode

 

*STOP [>> STOP]: Stop mode

 

following cue-up.

 

 

STILL [>> STILL]: Output still pictures in search mode.

 

 

 

 

 

 

 

 

 

 

 

 

PLAY START [> PLAY start]: Set the timing for switching from

 

16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY [>> 4

stop mode to playback mode.

 

 

 

delay]: The larger the numerical value, the longer the

In an editing system including an editing control unit such as

 

 

delay. By adjusting this setting, it is possible to reduce the

the PVE-500, you can adjust this setting so that the delay

 

 

phase synchronization time and preroll time during

before switching to playback mode is the same on all the decks

 

 

editing.

 

 

 

 

 

 

 

of the editing system. It is then no longer necessary to

 

Factory default setting: 5 FRAME DELAY [>> 5 delay] (for

synchronize the decks for editing, and the preroll time can be

 

 

DSR-1600A) or 4 FRAME DELAY [>> 4 delay] (for DSR-

shortened.

 

 

 

1600AP)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO REW [>Auto REW]: Select whether to rewind the tape

 

DISABLE [>> DISABLE]: Do not rewind the tape

automatically when recording or playback reaches the end

 

 

automatically.

 

 

 

 

 

 

 

of a tape.

 

 

*ENABLE [>> ENABLE]: Rewind the tape automatically.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Settings Menu 4 Chapter

Menu Contents 39