Connections for a Cut Editing System

The following figure shows a cut editing system

For details of connecting devices other than the DSR-

configuration which includes a DSR-1600A/1600AP unit

1600A/1600AP, refer to the instruction manual for each

as the player and a DSR-1800A/1800AP as the recorder.

device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A 75 Ω coaxial cable (not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B 9-pin remote control cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C Cable with RCA phono plugs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSR-1600A/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSR-1800A/

 

1600AP (player)

SDI OUT

SDI IN 1800AP (recorder)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REF.

 

 

 

 

 

 

VIDEO

 

 

 

 

 

 

OUT

 

 

VIDEO

AUDIO

REMOTE

 

VIDEO

AUDIO

REMOTE

OUT 2

MONITOR

 

OUT 2

MONITOR

(SUPER)

OUT

 

 

(SUPER)

OUT

 

1

3

2

1

1

3

2

Composite

Audio input

 

 

Composite

Audio input

 

video input

 

 

video input

 

 

 

 

 

REF.

 

 

 

 

PLAYER

 

VIDEO IN

 

 

Source monitor

Main monitor

RECORDER

Editing control unit (PVE-500, etc.) a)

a) For the settings on the editing control unit, see “Settings on an editing control unit” on page 56.

and Connections 5 Chapter

Settings on the DSR-1600A/1600AP (player) and DSR-1800A/1800AP (recorder)

Button

Recorder

Player

 

 

 

REMOTE

On (lit)

On (lit)

 

 

 

9PIN

On (lit)

On (lit)

 

 

 

For details of the video/audio input and audio mode settings for the recorder, refer to the DSR-1800A/1800AP Operating Instructions.

About reference video signals

In order to provide stable video and audio signals for analog editing, it is necessary for the built-in time base corrector (TBC) to operate correctly. To ensure this, input a reference video signal synchronized with the video signal to the REF. VIDEO IN connector.

Settings

Connections for a Cut Editing System

51