|
|
|
|
|
| P00 USER LOAD |
| ESC |
|
| DISPLAY MODE | : | ALL |
|
| 001.USER1 | JAN/01/04 |
| |
| 002.USER2 | JAN/15/04 |
| |
| 003.NO FILE |
|
|
|
| 004.USER4 | FEB/05/04 |
| |
| 005.USER5 | FEB/20/04 |
| |
|
|
|
|
|
|
|
|
|
|
5 Turn the MENU knob to move the b mark to the desired file number to be loaded, and press the MENU knob.
The message “LOAD OK? YES b NO” appears and the access indicator lights.
|
|
|
|
|
|
| P00 USER LOAD |
| ESC |
| |
| LOAD | OK? | YES | NO |
|
| DISPLAY | MODE | : | ALL |
|
| 001.USER1 | JAN/01/04 |
| ||
| 002.USER2 | JAN/15/04 |
| ||
| 003.NO | FILE |
|
|
|
| 004.USER4 | FEB/05/04 |
| ||
| 005.USER5 | FEB/20/04 |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
6 To carry out the load, move the b mark to “YES” and press the MENU knob.
To cancel, press the MENU knob leaving the b mark pointing to “NO”.
When the load is completed, the message “COMPLETE” appears and the access indicator goes off.
The USER FILE page appears again.
7 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
If data cannot be loaded
If one of the following error messages appears during or after the load operation, then the data was not loaded.
Data load error messages
Error message | Cause | Action |
|
|
|
NO MEMORY | No “Memory | Insert or reinsert the |
STICK (flashing) | Stick” is inserted. | “Memory Stick”. |
|
|
|
MEMORY STICK | Circuit or | Recheck, and |
ERROR | “Memory Stick” | consult your Sony |
(flashing) | fault. | representative. |
|
|
|
FILE ERROR | The “Memory | Do not try to load |
(flashing) | Stick” contains | data saved from |
| data that cannot | another camcorder. |
| be loaded into this |
|
| camcorder. |
|
|
|
|
7-2 Saving and Loading Scene Files
You can save various settings for shooting a particular scene as a scene file. Loading the scene file, you can quickly recreate setup conditions suitable for the scene. You can save up to five scene files in the camcorder memory and up to 100 scene files in a “Memory Stick”. You can also load data from the “Memory Stick” into the camcorder memory.
Data that can be saved in a scene fileYou can save the following data in a scene file:
•Values adjusted using the PAINT menu
For details of the PAINT menu, refer to the Maintenance Manual.
•Shutter speed settings made in the standard mode and ECS mode
•The white balance data included in a scene file depends on the SCENE WHITE DATA setting on the REFERENCE page of the FILE menu.
For details, see “White balance setting data to be saved in the scene file” on page 108.
7-2-1 Saving a Scene File
Proceed as follows to save a scene file in the camcorder memory or the “Memory Stick”.
Note
To save a scene file in the “Memory Stick”, insert the “Memory Stick” before starting the operation.
1 In the TOP menu, select the FILE menu.
2 Turn the MENU knob until the SCENE FILE page appears, then press the MENU knob to select the page. Alternatively, select “SCENE FILE” on the CONTENTS page to display the SCENE FILE page.
04 | SCENE FILE | TOP |
s1 | :STANDARD |
|
s2 | :STANDARD |
|
s3 | :STANDARD |
|
s4 | :STANDARD |
|
s5 | :STANDARD |
|
sSTANDARD |
|
| |
SCENE | RECALL | : | EXEC |
SCENE | STORE | : | EXEC |
F.ID: |
|
|
|
Data Setting User Loading and Saving 7 Chapter
107 | |
|
|