Item | Description |
|
|
LCD BRIGHT <L> | Adjusts the LCD brightness when the |
| LCD switch is in the L position. |
|
|
LCD BRIGHT <H> | Adjusts the LCD brightness when the |
| LCD switch is in the H position. |
|
|
LCD COLOR | Adjusts the color saturation of the LCD. |
|
|
i.LINK SBP2 | Selects whether or not to use the |
MODE | i.LINK connector SBP2 interface. |
|
|
REAR BNC OUT | Selects the type of the video signal to |
SEL | be output from the VIDEO OUT |
| connector. |
| SDI : Outputs the SDI signal. When |
| SDI is selected, connect the |
| VIDEO OUT connector to the SDI |
| IN connector of the video monitor. |
| VBS: Outputs the analog composite |
| video signal. When VBS is |
| selected, connector the VIDEO |
| OUT connector to the VIDEO IN |
| connector of the video monitor. |
| This setting allows you to save the |
| power. |
|
|
3 Turn the MENU knob to move the b mark to “REAR BNC OUT SEL”, and press the MENU knob.
The b mark on the left of “REAR BNC OUT SEL” changes to a z mark and the z mark on the left of the setting changes to a ? mark.
4 Turn the MENU knob to change the desired setting, and press the MENU knob.
The z mark on the left of the selected item changes to a b mark and the ? mark on the left of the setting changes to a z mark.
5 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
6-3-3 Setting the Color Temperature Manually
You can adjust the value of the white balance manually by setting the color temperature.
Proceed as follows.
1 Holding down the MENU knob, move the MENU ON/ OFF switch from OFF to ON.
The TOP menu appears.
2 Turn the MENU knob to move the b mark to “PAINT”, and press the MENU knob.
If this is the first time the PAINT menu has been displayed, the CONTENTS page appears. If the menu has been used before, the last accessed page appears.
3 If the CONTENTS page is displayed, turn the MENU knob to move the b mark to WHITE, and press the MENU knob to display the WHITE page.
If a different page is displayed, turn the MENU knob until the WHITE page appears, and press the MENU knob to select the page.
|
|
|
|
|
|
|
| P02 WHITE |
|
|
| ||
| COLOR | TEMP | <A>: | 3200 |
| |
| COLOR | FINE | <A>: | 0 |
| |
| R | GAIN |
| <A>: | 0 |
|
| B | GAIN |
| <A>: | 0 |
|
| D5600K |
| <A>: | OFF |
| |
| COLOR | TEMP | <B>: | 3200 |
| |
| COLOR | FINE | <B>: | 0 |
| |
| R | GAIN |
| <B>: | 0 |
|
| B | GAIN |
| <B>: | 0 |
|
| D5600K |
| : | OFF |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Item | Description |
|
|
COLOR TEMP | Sets the color temperature for the |
<A> | desired value. Adjust the value while |
| looking at the real image because error |
| tends to be bigger for adjustment of |
| high color temperature. |
|
|
COLOR FINE <A> | Adjusts the value more precisely when |
| the color temperature adjustment |
| through COLOR TEMP is not |
| satisfactory. |
|
|
R GAIN <A> | Only the value of R GAIN is changed. |
|
|
B GAIN <A> | Only the value of B GAIN is changed. |
|
|
D5600K | Sets the color temperature to |
| approximately 5600 K. |
|
|
The above table shows the adjustment of the white balance of channel A.
Items followed by “<B>” are used to adjust the white balance of channel B.
4 Turn the MENU knob to move the b mark to the item you want to set, and press MENU knob.
The b mark on the left of the selected item changes to a z mark and the z mark on the left of the setting changes to a ? mark.
5 Turn the MENU knob to change the setting, and press the MENU knob.
The z mark on the left of the selected item changes to a b mark and the ? mark on the left of the setting changes to a z mark.
To set other items, go back to step 3.
6 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
Settings Detailed and Displays Menu 6 Chapter
95 | |
|
|