When SCENE WHITE DATA is set to ON
The white balance setting data selected when you save the scene file is saved. For example, when the WHITE BAL switch is set to A, the adjusted values in memory A are saved in the scene file, and when the WHITE BAL switch is set to PRST, the preset value is saved.
When SCENE WHITE DATA is set to OFF
White balance setting data is not stored in the scene file.
5 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
Note
If files have been saved in the page selected in step 2, those files are replaced with files loaded from the camcorder memory. For example, files from 001 to 005 are replaced.
You can save five scene files from the camcorder to the “Memory Stick” in a single operation.
Proceed as follows.
1 After displaying the SCENE FILE page (see page 107) turn the MENU knob to move the b mark to “SCENE STORE” on the SCENE FILE page, then press the MENU knob.
One of the SCENE STORE pages appears.
2 Turn the MENU knob until the desired SCENE STORE page appears, then press the MENU knob.
P01 SCENE STORE | ESC | |
DISPLAY MODE | : | ALL |
001.SCENE1 | FEB/05/02 | |
002.SCENE2 | FEB/06/02 | |
003.NO FILE |
|
|
004.SCENE4 | FEB/08/02 | |
005.SCENE5 | FEB/08/02 | |
***.5FILE SAVE 
3 Turn the MENU knob to move the b mark to “5FILE SAVE B
The message “SAVE OK? YES b NO” appears.
|
|
|
|
|
|
|
| P01 SCENE | STORE | ESC |
| ||
| SAVE | OK? |
| YES | NO |
|
| DISPLAY | MODE | : | ALL |
| |
| 001.SCENE1 |
|
|
|
| |
| 002.SCENE2 |
|
|
|
| |
| 003.NO | FILE |
|
|
| |
| 004.SCENE4 |
|
|
|
| |
| 005.SCENE5 |
|
|
|
| |
| ***.5FILE | SAVE |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 To carry out the save, move the b mark to “YES” and press the MENU knob.
To cancel, press the MENU knob leaving the b mark pointing to “NO”.
When the save is completed, the message “COMPLETE” appears.
Setting the file ID
Before the data is saved as a scene file, it is useful to set a file ID to identify it. The set file ID is saved together with the data.
To set the file ID, proceed as follows.
1 On the SCENE FILE page, turn the MENU knob to move the b mark to “F. ID”.
F04 | SCENE FILE | TOP |
s1 | :STANDARD |
|
s2 | :STANDARD |
|
s3 | :STANDARD |
|
s4 | :STANDARD |
|
s5 | :STANDARD |
|
sSTANDARD |
|
| |
SCENE | RECALL | : | EXEC |
SCENE | STORE | : | EXEC |
F.ID: |
|
|
|
2 Press the MENU knob.
A character table appears, allowing you to select characters you want to enter.
U16 USER FILE | TOP |
INS DEL | RET | ESC | END |
sSTANDARD |
|
| |
SCENE | RECALL | : | EXEC |
SCENE | STORE | : | EXEC |
F.ID: | x |
|
|
3 Carry out the operations for steps 4 and 5 described in
Note
Set the file ID before saving the scene file in the “Memory Stick” or the camcorder memory. Otherwise, the file ID is not saved with the other data.
4 When you finish entering the file ID, turn the MENU knob to move the x mark to “END”, then press the MENU knob.
The SCENE FILE page appears again.
Data Setting User Loading and Saving 7 Chapter
109 | |
|
|