6-2-3 Display Modes and Setting

Change Confirmation/

Adjustment Progress

Messages

You can limit or suppress the messages that give details of setting changes and adjustment progress and results by setting a display mode.

The conditions under which messages are displayed and their correspondence with the display mode are as follows:

Setting change confirmation/adjustment progress messages

and display modes

Y: Message is displayed.

N: Message is not displayed.

Message

Message

Display

 

display

 

mode

 

condition

 

setting

 

 

 

 

 

 

 

 

1

2

3

 

 

 

 

 

When the filter

ND : n, CC : m (where n =

N

N

Y

selection has

1, 2, 3, 4, m = A, B, C, D)

 

 

 

been changed

 

 

 

 

 

 

 

 

 

When the gain

GAIN : n (where n = -3dB,

N

N

Y

setting has been

0dB, 3dB, 6dB, 9dB,12dB,

 

 

 

changed

18dB, 24dB, 30dB, 36dB,

 

 

 

 

42dB, 48dB)

 

 

 

 

 

 

 

 

When the

WHITE : n (where n = A

N

N

Y

setting of the

CH, B CH, PRESET) or

 

 

 

WHITE BAL

ATW : RUN

 

 

 

switch has been

 

 

 

 

changed

 

 

 

 

 

 

 

 

 

When the

DCC : ON (or OFF)

N

Y

Y

OUTPUT/DCC

 

 

 

 

selector has

 

 

 

 

been set to DCC

 

 

 

 

ON or OFF

 

 

 

 

 

 

 

 

 

When the

SS : 1/100 (PDW-510/530)

N

Y

Y

shutter speed

or 1/60 (PDW-510P/530P)

 

 

 

and mode

(or 1/125, 1/250, 1/500,

 

 

 

setting has been

1/1000, 1/2000,ECS, SLS)

 

 

 

changed 1)

 

 

 

 

When the black

E.g. WHITE : OK

N

Y

Y

or white balance

 

 

 

 

has been

 

 

 

 

adjusted

 

 

 

 

 

 

 

 

 

1)This is also displayed for about 3 seconds when the SHUTTER selector is set to ON.

Changing the display mode

The currently set display mode appears on the VF DISP 1 page of the USER menu. To change it, proceed as follows.

1 Follow steps 1 and 2 in 6-2-2 “Selecting the Display Items” on page 85, until the VF DISP 1 page of the USER menu appears on the screen.

2 Turn the MENU knob to move the b mark to “VF DISPLAY MODE”, and press the MENU knob.

The b mark on the left of “VF DISPLAY MODE” changes to a z mark and the z mark on the left of the setting changes to a ? mark.

3 Turn the MENU knob until the desired display mode appears, and press the MENU knob.

The z mark on the left of “VF DISPLAY MODE” changes to a b mark and the ? mark on the left of the setting changes to a z mark.

4 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.

6-2-4 Setting the Marker Display

Use the MARKER 1 page of the USER menu to switch the display of the center and safety zone markers on or off and to select whether the area indicated by the safety zone marker is 80%, 90% or 100% of the screen area.

CANCEL/PRST /

ESCAPE switch

MENU knob

MENU ON/OFF switch

1 Set the MENU ON/OFF switch to ON.

The last accessed menu page appears on the screen.

2 Turn the MENU knob until the MARKER 1 page appears, and press the MENU knob to select the page.

 

 

 

 

 

 

 

 

U07 MARKER

1

 

TOP

 

 

MARKER

 

 

:

OFF

 

 

CENTER

 

 

:

OFF

 

 

SAFETY

ZONE

 

:

OFF

 

 

SAFETY

AREA

 

:

90%

 

 

ASPECT

 

 

:

OFF

 

 

ASPECT

SELECT

:

4:3

 

 

ASPECT

MASK

 

:

OFF

 

 

ASPECT

MASK

LVL

:

1/4

 

 

100% MARKER

 

:

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

You can set the following items on the MARKER 1 page.

ItemDescription

MARKER

Not to display all markers, set to OFF.

Settings Detailed and Displays Menu 6 Chapter

6-2 Status Display on the Viewfinder Screen

87