-134-

For Machines Mfg. Since 3/11
Turn-Nad o® Gearhead Lathes PARTS
Front Machine Labels
Motor: 15 HP, 440V, 3-Ph, 60 HzFull-Load Current Rating: 19.23ASwing Over Bed: 18.11"Distance Between Centers: 60"Swing Over Cross Slide: 11.02"Swing Over Gap: 27.95"
Cross Slide Travel: 11" Made in Taiwan to South Bend Specifications
MODEL SB1057F
18" x 60" TURN-NADO®
GEARHEAD LATHE w/DRO
MFG Date:
Serial No:
®
TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY WHILE USING THIS MACHINE: 1. Read and understand manual before starting. 2. Always wear approved eye protection. 3. Make sure the machine is connected to a grounded power source. 4. Keep all guards in place. 5. DO NOT wear loose clothing, gloves, or jewelry; secure long hair and roll up long sleeves. 6. Disconnect power before service, maintenance, or adjustments. 7. DO NOT operate when tired or under the influence of drugs or alcohol. 8. Make sure the machine is properly adjusted/set up before starting. 9. Change cutting fluid regularly and avoid contact with skin. 10. Make sure workpiece is properly and securely held in the chuck and has safe clearance through full rotation before starting the lathe. 11. Never leave the chuck key in the chuck. 12. Never touch the chuck or workpiece when it is in motion. 13. Never leave the lathe running unattended. 14. Make sure long workpieces are properly supported. 15. Always use the proper speed rate for the material you are turning. 16. Do not allow children to have unsupervised access to the machine.Compound Travel: 5.39"Spindle Nose: D1-8Spindle Bore: 3.15"Spindle Taper: MT#7Tailstock Taper: MT#5Weight: 5170 lbs.WARNING!!
WARNING!
!
!INJURY/SHOCK
HAZARD
To avoid shock or
accidental starting,
disconnect power
before adjusting or
servicing machine.
All labels are shown at 100%
WARNING!
!
ENTANGLEMENT
HAZARD
WARNING!
!
EYE INJURY
HAZARD
Always wear ANSI
approved safety
glasses when using
this machine.
INJURY HAZARD
Do not use machine
if you have not read
the manual. Visit
southbendlathe.com
or call 360-734-1540
to get a manual.
WARNING!
!
SB1057F Labels (B) All labels are shown at 100%
WARNING!
!
EYE INJURY
HAZARD
Always wear ANSI
approved safety
glasses when using
this machine.
WARNING!
!
!INJURY/SHOCK
HAZARD
To avoid shock or
accidental starting,
disconnect power
before adjusting or
servicing machine.
INJURY HAZARD
chuck key from chuck
WARNING!
!
Sheets (MSDS) for
safety information.
WARNING!
!
!INJURY/SHOCK
HAZARD
To avoid shock or
accidental starting,
disconnect power
before adjusting or
servicing machine.
WARNING!
!
INJURY HAZARD
Always remove
chuck key from chuck
immediately after
making adjustments
to avoid serious
WARNING!
!
POISON/
BIOHAZARD
Refer to the cutting
fluid manufacturer’s
Material Safety Data
Sheets (MSDS) for
safety information.
WARNING!
!
ENTANGLEMENT
HAZARD
Remove or secure
loose clothing, hair
or jewelry to reduce
the risk of serious
injury or death.
Always wear ANSI
approved safety
glasses when using
this machine.
or call 360-734-1540
to get a manual.
WARNING!
!
Only trained and properly supervised personnel are allowed to operate this machine. If safe operation procedures are not clearly understood, requestadditional training from a supervisor before beginning operation.NOTICE
ONE SHOT
OILERbolt before engaging the carriage
leadscrew.
2
3
NOTICELoosen the carriage lock bolt before engaging the carriage
leadscrew.
4,8,12,16,20,24,28,32,36,40,44,48,56,60,72Any PositionIn.Non-Numbered
Position
Numbered
Position
1,2,3,4
Position
1,3 or 2,4
Position
1 Only2,6,10,14,18,22,26,30,543,5,7,9,11,13,15,19,23,272½,3½,4½,7½,11½,13½2¼,2¾,3¼,3¾
27∕8
1
2
3
4
Same as Metric Threads
ONE SHOT
NOTICEFactory must verify accuracy of this label
Located above
cutting fluid tank
access panel
SB1057F Labels (B)
WARNING!
!
!INJURY/SHOCK
HAZARD
To avoid shock or
accidental starting,
WARNING!
!
INJURY HAZARD
Always remove
chuck key from chuck
immediately after
making adjustments
to avoid serious
personal injury.
All labels are shown at 100%
!
!
HAZARD
loose clothing, hair
or jewelry to reduce
the risk of serious
injury or death.
WARNING!
EYE INJURY
HAZARD
Always wear ANSI
approved safety
glasses when using
this machine.
SB1057F Labels (B)
WARNING!
!
!
All labels are shown at 100%
WARNING!
!
ENTANGLEMENT
HAZARD
Remove or secure
loose clothing, hair
or jewelry to reduce
the risk of serious
injury or death.
WARNING!
!
EYE INJURY
HAZARD
Always wear ANSI
approved safety
glasses when using
this machine.

South Bend Lathe Co.

MODEL SB1057F18" x 60"TOOLROOMLATHE
2101
2102
2103 2104
2105
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
2117
2116