Rear Machine Labels, 21182103 | Southbend SB10146PF specification

For Machines Mfg. Since 3/11

P A R T S

Turn-Nado®Gearhead Lathes

Rear Machine Labels

21182103

!

!WARNING!

INJURY/SHOCK

HAZARD To avoid shock or accidental starting, disconnect power before adjusting or servicing machine.

!

!WARNING!

INJURY/SHOCK

HAZARD To avoid shock or accidental starting, disconnect power before adjusting or servicing machine.

2103

440V

3-Ph

2119

REF	PART #	DESCRIPTION
2103	PSBLABEL02HL	DISCONNECT POWER LABEL HL
2118	PSBLABEL15L	ELECTRICITY LABEL

REF	PART #	DESCRIPTION
2119	PSB1048PF2119	440V 3-PHASE LABEL

The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at (360) 734-1540 or www.southbendlathe.com to order new labels.

-135-

Image 137

Southbend SB10146PF owner manual Rear Machine Labels, 21182103

Contents

Lathe w/DRO TURN-NADOGEARHEAD Customer Service UpdatesScope of Manual Manual Feedback Table of Contents Accessories Maintenance About This Machine FeaturesForeword Capabilities General identification Model SB1058F shown General Identification Headstock Master Power SwitchControls Components Carriage Control Panel Tailstock Carriage Feed Clutch Knob Foot brake and spindle levers Safety Foot Brake Product Specifications Main Motor Tailstock Information Construction Model Number SB1056F SB1057F SB1058F Main Motor Leadscrew Length 65.71 85.39 105.08 Steady Rest Capacity Construction Understanding Risks of Machinery Basic Machine Safety F E T Y Additional Metal Lathe Safety Additional Chuck Safety Typical preparation process is as follows Preparation OverviewThings Youll Need Availability Power Supply RequirementsFull-Load Current Rating Circuit Requirements 440V Operation Grounding Requirements Unpacking Installed & Not Shown QtyInventory Main Inventory 1 Figure Qty Basic steps for removing rust preventative Cleaning & ProtectingBefore cleaning, gather the following Location To lift and move the lathe Lifting & Moving Leveling Leveling & Mounting Bolting to Concrete Floors Assembly Adding Coolant Power ConnectionLubricating Lathe Hot Connecting Power To test run your machine Test Run Engaged E P a R a T I O N Factory adjustments that should be verified Recommended AdjustmentsSpindle Break-In To perform the spindle break-in OperationPERATIONOverview Chuck & Faceplate Mounting Installation & Removal Devices To install the chuck Chuck Installation To remove the chuck Chuck RemovalRegistration Marks Mounting Workpiece Scroll Chuck ClampingJaw Chuck Jaw tightening sequence Faceplate Tailstock Using QuillPositioning Tailstock To mount a non-concentric workpiece to the faceplate To install tooling in the tailstock Installing Tooling Removing Tooling Offsetting TailstockTo offset the tailstock Tools Needed Qty To align the tailstock to the spindle centerline Aligning Tailstock to Spindle CenterlineItems Needed Qty Dead Centers Centers Mounting Dead Center in Spindle Live CentersRemoving Center from Spindle Mounting Center in Tailstock Mounting Workpiece Between Centers Removing Center from Tailstock Steady Rest To install and use the steady rest Compound Rest Follow RestTool Needed Qty To set the compound rest at a certain angle Four-Way Tool Post To install a tool in the tool postAligning Cutting Tool with Spindle Centerline 5 = To align the cutting tool with the tailstock center Micrometer StopTop View Side View Spindle Speed Manual Feed RPM or lower when using the high H gearbox range Power FeedSetting Spindle Speed Gearbox range lever Power Feed Controls Apron feed selection and direction knobs Example Power Feed Rate of 0.0025/rev Setting Power Feed Rate Alternate End Gear Configuration Standard End Gear ConfigurationConfiguring End Gears To configure the end gears Example Metric Thread Pitch of 2.5mm Threading ControlsHeadstock & Gearbox Threading Controls Disengaged Apron Controls TPI Divisible By Thread Dial ChartThread Dial Odd Numbered TPI Even TPI Not Divisible By⁄2 Fractional TPI ⁄4 or 3⁄4 Fractional TPI Coolant System Chip Drawer To use the coolant system on your lathe Rod Support SB1279-10 Pc. Precision 5-C Collet Set AccessoriesSB1272-Collect Attachment SB1271-Taper Attachment Maintenance Schedule Maintenance Checking & Adding Oil LubricationChanging Headstock Oil Items Needed Qty Adding Oil Quick-Change GearboxChecking Oil Level Draining Oil ApronDraining Oil & Flushing Reservoir Checking Oil Level Location of one-shot oiler on the apron One-Shot Oiler Ball Oilers Longitudinal Leadscrew Lubricating End GearsHandling & Care Hazards Coolant System Service To change the coolant Adding FluidChanging Coolant To prepare the lathe for storage Machine Storage Cross Slide Backlash AdjustmentCompound Rest To remove leadscrew end play Leadscrew End Play AdjustmentGib Adjustment Front saddle gib adjustment screw Carriage Lock Clamp To adjust the half nut Half Nut AdjustmentTo adjust the V-belts Belts To adjust the spindle clutch Spindle Clutch Adjustment Symptom Required Action Engaging adjustment ring reverse side Shown To replace the shear pin Leadscrew Shear Pin Replacement Shear pin access Gap Removal Gap Insert Removal & Installation Gap Installation Symptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Wiring Diagram Color KEY Electrical Safety Instructions To correct wiring that is out of phase Correcting Phase Polarity Wiring Overview Visual index Component Location Index Electrical Cabinet Electrical box Electrical Box Coolant Pump Spindle Motor Control Panel Control panel wiring To Electrical Box, Additional Components Power Supply Connection Headstock Housing 101 Description Headstock Housing Parts List Headstock Gears 104 Shaft Headstock Gears Parts List 106 Gearbox 108 Gearbox Parts List 110 Apron 112 Apron Parts List 114 705 Oil PR03M EXT Retaining Ring 12MM Motor & Headstock Oil System Parts List Saddle 119 Saddle Parts List Tool Post & Compound Rest Bed & Shafts Lathe BED GAP SB1056F Bed & Shafts Parts List Stands & Panels SB1046PF-47PF, SB1056F-58F Description Stand & Panels Parts List SB1046PF-47PF, SB1056F-58F Stand & Panels SB1048PF PSS34M Stand & Panels Parts List SB1048PF Mounting Block Brake 14121409 1400 Thread Dial Micrometer Stop 1705 1706 1707 1709 1710 1711 1712 1713 Steady Rest Follow Rest Control Panel viewed from behind Electrical Cabinet & Control Panel 2019 2001 2003 South Bend Lathe Co Front Machine Labels 21182103 Rear Machine LabelsPage Warranty Southbendlathe.com