Manuals / Brands / Laundry Appliance / Washer / Speed Queen / Laundry Appliance / Washer

Speed Queen TMB796C To Reverse the Loading Door, A, H, S and U models after serial number, •Close steam valve to steam tumbler before servicing

1 62

Download 62 pages, 2.25 Mb

22

Installation

To Reverse the Loading Door

A, H, S and U models after serial number 0308001307

The tumbler is delivered with a right hinged door, but the door can be changed to a left hinged position.

WARNING

To reduce the risk of electric shock, fire, explosion, serious injury or death:•Disconnect electric power to the tumbler before servicing.•Close gas shut-off valve to gas tumbler before servicing.•Close steam valve to steam tumbler before servicing.•Never start the tumbler with any guards/ panels removed.

•Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumbler is properly grounded.

W002

1.Disconnect power supply to tumbler.

2.Unlock and remove control panel. Remove two control assembly mounting screws from right side. Swing open control to access upper flange right guide lug assembly. Refer to Figure 6.

3.Remove lint panel.

IMPORTANT: Support door and hinge assembly securely to prevent it from dropping once side screws are removed from door hinge lug.

1

8

7

5	2

4

3

4

5

6

TMB1994N

TMB1994N

1Control Assembly Mounting Screw

2Control Assembly

3Guide Lug Assembly

4Side Screw

5Screw

6Lint Panel

7Front Panel

8Control Panel

Figure 6

20

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

M414905

Contents

Page Page In the U.S.A In Canada In Australia WARNING •WHAT TO DO IF YOU SMELL GAS: –Do not try to light any appliance –Do not touch any electrical switch; do not use any phone in your building –Clear the room, building or area of all occupants Table of Contents Steam Requirements Single Drop Timer Rotary Coin Drop Timer Adjustments Removing Tumbler from Service Introduction Model Identification Introduction Customer Service Wiring Diagram Serial Plate Location Safety Information Save These Instructions Important Safety Instructions Page Specifications and Dimensions Cabinet Dimensions Exhaust Outlet Locations Gas Connection Locations Electrical Connection Locations Steam Connection Locations Installation Pre-InstallationInspection Location Requirements Position and Level the Tumbler Bolt-OnAngle Option Page To Reverse the Loading Door Page Page Before Placing Tumbler into Service Required for CE Models Only Installing CE Gas Drying Tumblers General Information Supply Burner Country Orifice Capacity Basic Configuration Specific Conversion Procedures NOTE: Blank burner orifices are Part No. M400995 Page Exhaust Requirements Layout Make-UpAir Venting Individual Venting Manifold Venting Page Station 8 in. (203 mm) Duct 10 in. (254 mm) Duct Page Gas Requirements Use pipe compound, resistant to actions of L.P. gas, on all pipe threads Gas Supply Pipe Sizing and Looping Equivalent Length 25 feet 50 feet 75 feet 100 feet High Altitude Burner Orifice Sizing Electrical Requirements Grounding Instructions For CE Models Only Service/Ground Location To Connect Electrical Service To The Tumbler Page Jumper Configuration Instructions Ferrite Ring Installation 50 Pound Gas and Steam Models 75 Pound Gas and Steam Models 50 and 75 Pound Electric Models Steam Requirements Piping Recommendations Thermal Oil Prep Steam Pressure PSI (bar) Minimum Pipe Diameter Steam Trap Size (Pounds Condensate/Hour) Single Drop Timer Power-UpMode Ready Mode Start Mode Run Mode Dipswitch Settings Coin Pulse (in Minutes) Rotary Coin Drop Timer Installing Accessory Timing Cam Removal of Existing Timing Cam Installation of New Timing Cam Adjustments Gas Burner Air Shutter Airflow Switch Gas and Electric Tumblers Page Loading Door Switch Loading Door Catch Drive Belt Nonreversing Models Reversing Models Page Page Removing Tumbler from Service