Validation Operation | Star Micronics 150 specification

Control Codes

PcOS Series 150

Programmer's Guide

Validation Operation

Validation Operation

The form is inserted from the top and extends out the left side and/or top of the printer. It rests on a fixed stop. A maximum of 16 lines at 40 characters can be printed on a form. In this manual, top insertion will be termed validation mode.

Function	Open for validation
ASCII	[ESC] [DC1]
Hexadecimal	1BH 11H
Decimal	<27> <17>
IPCL	&%VO
EPOS	[ESC] c 0 <n>
Description	This command opens the form compensation assembly for validation. No
	automatic validation form sensing is performed. The application must poll
	the printer for validation forms present and then issue a close
	compensation command.

Function	Close for validation
ASCII	[ESC] [DC3]
Hexadecimal	1BH 13H
Decimal	<27> <19>
IPCL	&%VC
EPOS	[ESC] c 0 <n>
Description	This command closes the form compensation assembly for validation. No
	automatic validation form sensing is performed.

Function	Close for validation when form is sensed
ASCII	[ESC] [DC4]
Hexadecimal	1BH 14H
Decimal	<27> <20>
IPCL	&%VS
EPOS	[ESC] c 0 <n>
Description	This command closes the form compensation assembly for automatic
	validation form sensing by the printer.

Page 52

Rev G

12/14/99

Image 62

Star Micronics 150 manual Validation Operation

Contents

Programmers Guide Page Change History Programmer’s Guide PcOS Series Disclaimer PcOS Series DisclaimerCopyright Table of Contents Table of Contents PcOS Series Programmers Guide PcOS Series Table of Figures Table of Figures Page Chapter Overview of the Series 150 Printer Warranty InformationWhat is in this book? Contacting Ithaca Peripherals Where can you find more information?Overview PcOS Series Series 150 Models Standard FeaturesChapter General Description Model 153 Receipt/Journal/Validation Printer Model 151 Receipt PrinterModel 152 Receipt/Journal Printer Model 154 Receipt/Validation Printer Programmers Guide PcOS Series 150 General Specifications Chapter General SpecificationsPrinting Specifications General Specifications Character Generation General Specifications Physical Specifications Electrical Characteristics Ribbon Media SpecificationsInterface Specifications Receipt Paper Receipt Printing Printable AreaReceipt/Journal Paper Validation Forms Printing Validation Top Insertion Validation Left-side Insertion Control Codes Overview PcOS Series Chapter Control Codes OverviewNomenclature Ipcl Codes Programmers Guide PcOS Series 150 Control Codes OverviewStandard Emulation Epos Emulation NCR2567 Emulation Tables and ChartsApplication Development Telpar Emulation Programmers Guide PcOS Series Control Codes Chaper Printer Control CodesPrint/Paper Motion Low-level Paper Motion Control Control Codes PcOS Series Horizontal Motion Control Horizontal Motion Vertical Motion Control Increments Control Codes Function Vertical tab Function Set form length in lines Character Font Function Begin 90 rotated font International Character Sets and Code Pages Ascii LanguageCountry Code Epson Language Set Function Select character code Character Code Function Character font image download Euro Character Substitution Matrix IBM Character Print Control NLQ HSD Character Pitch Examples of character print Character Pitch Pitch Spacing Character Attribute Commands Performs an auto print Character Attributes PcOS Series Control Codes Function Begin underline Ascii ESC F Function Select superscript Function End italics Print Rotation Commands Number lines per inch Rotated Print Function Begin 270 rotated print Function End rotated print Function Set rotated print line spacing Graphic Mode Standard APA Graphics Graphic Mode Function Begin unidirectional print Bar codes EAN-8 Function Bar code height Receipt Paper Out Sensor Validation Operation Validation Operation Control Function Set left/right print margin Miscellaneous Control Miscellaneous Control Function Print suppress and data pass through Function Enable Dynamic Response Parallel, Non-IEEE 1284 Mode Inquire Printer Status Set/Inquire Dynamic Response Mode Serial Mode InquireParallel, Ieee 1284 Mode Inquire Programmers Guide PcOS Series Control Codes Inquire Commands Function Inquire form position sensor status Function Request printer reset Function Inquire printer state Function Inquire all printer status Function Inquire printer ID Extended Diagnostic Commands ACK Epos Codes Epos Command SummaryCommand Comment Description Real-time Status Epos Codes ESC Command Descriptions Epos Deviations Epos Deviations Function Enable/disable panel buttons Function Set bar code Microline Codes Microline Command SummaryCommand Description Bell Communication Echo Mode Serial interface only Star Codes Star Command SummaryCommand Description Control codes used in character setting Control codes used in line spacing Control codes used for peripheral units Control codes used for graphic printingESC a Other control codes DLE NCR Command SummaryNCR2567 Codes ETB Telpar Command Summary Telpar Codes Code Field Control Codes Summary by CodeNormal Second Hex Code Ipcl equivalent Description 1BH,3DH ESC 1BH,3AHESC 1BH,3CH ESC 1BH,3EH ESC 1BH,5EH ESC 1BH,5AHESC 1BH,5DH ESC 1BH,5FH 1BH,7EH Code Field Print/paper motion Control Codes Summary by FunctionProgrammers Guide Vertical motion Character pitch International Character SetsCustom characters Character attributes Rotated print Graphics 4AH DiagnosticsBar codes Validation control Green Red Indicator Push Buttons Momentary SwitchesIndicators Chapter Operator Panel Controls Fault Indicators Operator Panel Controls PcOS Series Chapter Product Self-tests Level 0 DiagnosticsExtended Diagnostics Self test Chapter Hex-dump Mode Hex-dump Mode PcOS Series Manual Configuration13 Chapter Configuration ModeInitial Power on Enable Remote Configuration General Recommendation Feature ConfigurationConfiguration Mode PcOS Series Epos Microline Programmers Guide PcOS Series Configuration Mode Rev G 12/14/99 Vertical Control Character Configuration Mode PcOS Series USA Configuration Mode PcOS Series Programmers Guide XON/XOFF DTR/RTS General Control Options Configuration Mode PcOS Series Interface Vertical ControlCharacter Options Save Changes Chapter Communications Protocol and Print Buffers Overview Communications PcOS Series Overview Programmers Guide PcOS Series Parallel Port Parallel Port Protocol Printer Buffer Size Parallel Port Inquire Ieee Communications PcOS Series Time-out Parallel Port Inquire Non-IEEE PE to ENQ request timing Parallel Port Plug and Play Parallel Port Connector Signal Levels Serial Port Pin-out Serial Port FeaturesSerial Port Serial Port Flow Control Using DTR Serial Port Protocol XON/XOFF Print Buffer Flow Serial buffer operation Programmers Guide PcOS Series Print controller using data Printer Buffer Size Serial Port Inquire Inquire flow Reset in Serial Mode Remote Printer ResetPower-cycle Recovery Reset in Parallel Mode Programmer’s Notes Interface Description Interface ConnectorsChapter Cash Drawer Interface Function Drawer Printing Graphics PcOS Series Chapter Printing GraphicsCharacter Graphics Printing Graphics APA Graphics Receipt with APA graphics 0100 Programmer’s Guide Code Country Code Decimal Hex Appendix a Language TablesProgrammers Guide PcOS Series 150Appendix a Epson ID 3H,0FAH Appendix a PcOS SeriesECMA-94 3H,0FCH Appendix B Ascii Code Chart Programmer’s Guide PcOS Series Appendix B Appendix C PcOS Series Appendix C Ordering CablesGeneral Information Index Programmers Guide PcOS Series Index APA graphic file 124 Ascii Chart 129 Index PcOS Series PcOS Series Insert PN Rev G 12/14/99