Delta User’s Manual | Star Micronics specs

6	Delta User’s Manual

Paper press bar

\

Release lever

‘-__

‘igure l-5. Inserting a single sheet ofpaper can be done “under power” with the ne feed button.

Now, instead of rolling the paper in manually by turning the platen knob, we’re going to use the L.F. button, with the power switch turned on. (This means we’ll have to use the “F” (friction feed) position of the release lever.) Remember what we told you about that L.F. (line feed) button? This allows you to advance the paper one line at a time, and if you hold the button down, you’ll get multiple line feeds, one after the other.

OK? Now let’s start.

1.Remove the printer cover and tractor unit (you can leave the paper guide and paper separator on if you have installed them).

2.Turn the power switch on.

3.Lift up the paper press bar.

4.Set the release lever to the “F” position.

5.Insert the sheet from the back side of the platen (between the paper chute and the platen cover plate).

6.Press the ON LINE button until the ON LINE light goes off.

7.Press the L.F. button to roll the paper in until it appears on the front side of the platen, about where you want the first line to start printing.

--

-

-

_

__

-

_

Image 18

Star Micronics user manual Delta User’s Manual

Contents

Delta User’s Manual @Copyright 1983 Star Micronics, Inc Special Message to the New Owner Delta User’s Manual Table of Contents Special Features Delta Printer Formatting Your OutputCreating Your Own Characters Getting It All Together Maintenance Appendix D TRS-60 Computers Appendix E Osborne, Kaypro and CP/M ComputersAppendix F Atari 400/800 Computers Appendix Commodore VIC-20 Computers Appendix DIP Switch SettingsAppendix Character Style Charts Appendix Delta User’s Manual Consumer Response 309 DIP Switch Quick ReferenceWarranty Inside Back Cover Command Quick Reference Serial busy protocols XONlXOFF Protocol ACK protocol Index Tables Xii Delta User’s Manual Closer Look Paper separator and paper guide used with roll paper Roll paper holder and holder shaft used only with rollPage Parallel interface connector the place where you hook Paper Selection and Loading Loading single sheets Delta User’s Manual Loading roll paper Delta User’s Manual Closer Look Loading sprocket-feed paper Open the tractor covers to expose the sprocket teeth Bottom feeding Delta-15 Figure I-10.Delta ready to run with sprocket-feed paper Delta User’s Manual Ribbon Installation Self-Test Closer Look Delta User’s Manual Getting Started With Delta Using Commercial Sojtware Getting Started With Delta First, some terminology Ascii Using Delta with SuperCalc Using Delta with word processorsPage Using this book without learning Basic Getting Started With Delta List OPEN4,4 CMD4 List PRINT#4 CLOSE4Establishing communications NEW LPRINTCHR$7 RUN NEW Lprint Testing RUNNEW CHR$ function NEW LPRINTCHR$27CHR$52 2$3LPRINT Testing RUN Escape Code Some problem codes ESC$=CHR$27 l@ LPRINTESC$ Delta User’s Manual Printing Text With Delta Chapter Lprint Condensedis the Narrowestpitch Print pitch Commands@ Lprint this is Elite Pitch Printing Lprint NOW WE are Back to Pica Pitch Printing I s LPRINTCHR$27W CHR$@NOW Were Back to NormalExpanded print H153 Lprint NOW WE are Back to Unexpandedpica Printing Print CommandsLPRINTCHR$14EXPANDEDELITE Pitch Making Delta print darker Print EmDhasis a Commands Lprint this is DOUBLE-STRIKEPRINTING Italic Commands Italic printing UnderJining Superscripts and subscripts Superscript Subscript commands NEW Lprint Thisline UsesMixing modes Build Instructionset REGULAR.HEADING$= STRING$27,*+ Regular LPRINTRESET.ALL$Lprintelites Elite LPRINTPICA$ Pica LPRINTRESET.ALL$ Return Return If Pica = False then LPRINTFOUR.DOT$ GOTO3590 Italics = False LPRINTROMAN$Repeatwith Italics If ENLARGED= True then Lprint Here is the chart it produces Control Code FunctionPage Delta User’s Manual Line Spacing and Forms Control Changing Line Spacing This is what you will get Line spacing Commands Run the program again. Now the results will look like this NEW Lprint Linenumber Moving down the page without a carriage return Forms Controls Form feed Form length commands Changing the Page Length Top and bottom margin commands Lprint PAY to the Order LineSpacingandFormsControl51 Summary Control code ESC Delta User’s Manual Formatting Your Output NEW Lprint ONECHR$9TWOCHR$9THREE CHR$9 Four One-shot tab command Left and right margin commands 5B END 13@ Lprint Return LPRINTCHR$27P CHR$l@ CHR$Z@CHR$@ One-shot vertical tab command Control Code Function LChapter Now hear this Bell commands Initializing Delta Printing to the bottom of the sheet Some Miscellaneous commandsPutting Delta to sleep Unidirectional printing Lprint Lprint NextPrinting Direction Lprint Work NEW Lprint Backspacedoes notLprint I===WORK Lprint Deletedoes not Backspace and delete Block graphics characters and special symbols Eighth Bit controls 3pl Lprint I II=11CHR$ICHR$9 4pI Next I Lprint Next J International Character set commands International character setsMacro control code Macro instruction Commands OFF Regularprint StartdefinitionMacro Lprint CHR$18 Pica END Macro Function Bell Disable bell Enable bell Reset Off-lineOn-line Control code Delta User’s Manual Creating Your Own Characters Dot Matrix Printing 000 0 eeeS&fee Defining Your Own Characters Rule I Download characters are seven dots high Rule 2 Dots cannot overlap 8WRONG Add up each column of dots Creating YourOwn Characters Download character definition command Assigning a value to your character Character designs for the four card suits Next M Figure Y-10. The attribute byte n2 for our heart character Printing Download Characters LPRINTCHR$27CHR$36CHR$@ DEFINTA-Z Next Lprint Return Read X LPRINTCHR$XNext J DECKCARD=X Next Card Return LPRINTSUIT$SUIT Download Character dejfinition commands Proportkmal Characters 12@ Lprint CHR$BITS 138 Next Only Difference Is the way They Are Accessed Creating Your Own Characters Lprint DEF.DOWN.CHAR$ NUMERAL.BOT$NUM= CHR$ASCII+ 2 + CHR$ASCII+ Mixing Print Modes with Download Characters Utility Program Gosub 950RETURN Gosub 660 Return REM **** Display Menu for Edit Mode Summary