At rated rpm, Exciting coil | Subaru Robin Power Products R1200

8-7 IGNITION COIL

Measure resistance in the coil of the ignition coil unit with a circuit tester.

	!	Measurement location
Resistance	(	Measurement location
	I
13K!G?		Measure the resistance between the black cord and the high

itension cord.

Note: The measured value does not always match the values shown in the table above because of errors by the circuit tester, unevenness of coil winding, or peripheral

temperature.

8-8 EXCITING COIL

Measure resistance of the exciting coil and voltage at the rated rpm with a circuit tester.

	Resistance value	(	Voltage (AC)	:	Measurement location
	Resistance value	I	at rated rpm	1	Measurement location
		I	at rated rpm	1
		I			Between the terminals of the
		I	10 Q 3ov	;
			10 Q 3ov	;
		I		i	exciting coil
		I

Note: The measured value does not always match the values shown in the table above, because of errors by the circuit tester, unevenness of coil winding, or peripheral temperature.

- 27 -

Image 31

Subaru Robin Power Products R1200 service manual At rated rpm, Exciting coil

Contents

Rozh -J &ii Foreword Contents Assembly Items Specifications AC Output Power Factor Rated 800 W Frequency 50 Hz Voltage 110 Output Max Output Max Under no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC Output Features CHOKE-RUN-STOP Component Identification Function of Each Component L-5 Camshaft 4CONNECTING ROD and PistonMain Bearing Cover Crankshaft Carburetor AIR Cleaner Description of Main Operations ‘CC Voltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each Component One section, replace with Assy 83 AVR Windings, or peripheral temperature Resistance Cleaning of Slip RingValue El 10.7J-z Exciting coil At rated rpm Disassembly and Assembly Driver Precautions Tools Precautions Nection Description M5 x 8 screws SequenceI Part to remove j IFront cover DescriptionI2 Remove the front cover By unscrewing three Damage the fuel Pipe Description PrecautionsPart to Sequencej remOve Be careful not to Lpanner Part to Sequence, removeSpanner Part to Remove $Ez End cover Description Precautions@ Driver Remove the connector Assembling, be That 1wiring See Fig. g-3-10 RemOve ’Rear ‘bracket Description Pull away the stator cover SequenceI Rpearfito~~ Description’ plastic hammer Siw‘ Part to / Sequencej remove ’ JFront Ibracket Description Necessary Precautions13 m/m box Spanner RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housing Necessary Precautions . tools @ Driver ’Governor Remove the governor lever j Lever Precautions Bolt has only to be loosenedOne M6 x 12 bolt Brace nuts 112m/m box ’spanner 10 m/m box jspanner Crank case by taking 26 i &cocci*nRemove the starting pully Ignition coil from Retainer Pull out the intake valve and the exhaust valveNotch Spanner 1spring retainer’s Front and hook ’ the minus driver Camshaft Description ISequenceI Part toCrankcase Tappets to distin Guish them from one Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will break Assembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pin Tappets and Camshaft Connecting ROD Intake Valve and Exhaust Valve =53 WV&e h valve guide clearance Breather Plate and Tappet Cover Cylinder Head Tappet Adjustment Ignition COIL, Exciting COIL, Flywheel and Starting Pulley Ignition PlugGovernor Lever Speed Control Muffler and Muffler Cover Nut 1’7 Recoil Startor Head Cover and Blower Housing Front Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe Connection Connection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For Adjustment Uel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring Diagram Maintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095