Ignition Plug, Governor Lever | Subaru Robin Power Products R1200

9-4-10 IGNITION PLUG

* Torque for the ignition plug: 230 ad250 kg-cm

(As for a new one (head plug): 120 s 150 kg-cm)

9-4-11 IGNITION COIL, EXCITING COIL, FLYWHEEL AND STARTING PULLEY

(a)Temporarily set the ignition coil and exciting coil in the crankcase and install the flywheel in the crankshaft. Clamp the starting pulley together with the flywheel.

Note: Installment should be done after wiping away any oil from the crankshaft and taper section of the flywheel.

Torque for the flywheel: 600 Q 650 kg-cm

(b)Measure air gap between the ignition coil, exciting coil and the flywheel and then clamp the ignition coil.

The air gap is 0.4 s 0.5 mm.

9-4-l 2 CARBURETOR

In the part of crankcase cylinder, install the gasket, insulator, gasket, carburetor, gasket, control bracket, and gasket, in this order. Then install the air cleaner body and secure it with two M6 flange nuts. Also lock the air cleaner body with Ml6 x 10 flange bolts.

Torque for the air cleaner clamping: 70 Q 90 kg-cm

Note:Set the control bracket at the position of “RUN”, and then mount it onto the air cleaner.

9-4-13 GOVERNOR LEVER

The governor used in the engine of this generator is of centrifugal weight type and is joined with

the governor lever. With the governor lever, the throttle valve of the carburetor is automatically regulated, therefore the engine speed is kept constant under load fluctuation.

Regulation procedure is as stated below (See Fig. 9-4-14, and Fig. 9-4-15)

(1) Join the carburetor throttle lever with the governor lever and install them in the governor shaft.

(2) Install the speed control in the cylinder head.
(3)	Join the governor and the speed control with		the governor spring.
		,
	a@==-
	,,
	//ylIr;;L
	SE+
	- @/-!
	!zsc-
	2s
	j&f-&
	$T,+,		Governor Lever
	cc=+
	\.T<I’
	&G
	‘L--		Governor Lever	Locking Nut
	‘L--
		F&. 9-4-14

-55-

Image 59

Subaru Robin Power Products R1200 service manual Ignition Plug, Ignition COIL, Exciting COIL, Flywheel and Starting Pulley

Contents

Rozh -J &ii Foreword Contents Assembly Items Specifications AC Output Power Factor Rated 800 W Frequency 50 Hz Voltage 110 Output Max Output Max Under no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC Output Features CHOKE-RUN-STOP Component Identification Function of Each Component L-5 Camshaft 4CONNECTING ROD and PistonMain Bearing Cover Crankshaft Carburetor AIR Cleaner Description of Main Operations ‘CC Voltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each Component One section, replace with Assy 83 AVR Windings, or peripheral temperature Value El 10.7J-z Cleaning of Slip RingResistance Exciting coil At rated rpm Disassembly and Assembly Driver Precautions Tools Precautions Nection Description M5 x 8 screws SequenceI Part to remove j IFront cover DescriptionI2 Remove the front cover By unscrewing three Damage the fuel Pipe Description PrecautionsPart to Sequencej remOve Be careful not to Spanner Part to Sequence, removeLpanner Part to Remove $Ez End cover Description Precautions@ Driver Remove the connector Assembling, be That 1wiring See Fig. g-3-10 RemOve ’Rear ‘bracket Description ’ plastic hammer SequenceI Rpearfito~~ DescriptionPull away the stator cover Siw‘ 13 m/m box Spanner Necessary PrecautionsPart to / Sequencej remove ’ JFront Ibracket Description RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housing Necessary Precautions . tools @ Driver ’Governor Remove the governor lever j Lever Precautions Bolt has only to be loosenedOne M6 x 12 bolt Brace nuts 112m/m box ’spanner 10 m/m box jspanner Crank case by taking 26 i &cocci*nRemove the starting pully Ignition coil from Retainer Pull out the intake valve and the exhaust valveNotch Spanner 1spring retainer’s Front and hook ’ the minus driver Crankcase Tappets to distin Guish them from one ISequenceI Part toCamshaft Description Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will break Assembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pin Tappets and Camshaft Connecting ROD Intake Valve and Exhaust Valve =53 WV&e h valve guide clearance Breather Plate and Tappet Cover Cylinder Head Tappet Adjustment Governor Lever Ignition PlugIgnition COIL, Exciting COIL, Flywheel and Starting Pulley Speed Control Muffler and Muffler Cover Nut 1’7 Recoil Startor Head Cover and Blower Housing Front Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe Connection Connection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For Adjustment Uel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring Diagram Maintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095