Part to Sequencej remOve | Subaru Robin Power Products R1200

1 Part to Sequencej remOve

6Fuel pipe ‘and plug (Discon- inection)

’			I	Necessary
	Description	Precautions	j	tools
			I	tools

(1)Remove the cap from the ’ fuel strainer and take out the gasoline from inside the fuel tank.

(2)With pliers, hold the fuel pipe clamp which is in- serted in the fuel strainer and pull it forward to remove the fuel pipe from the strainer.

I(3) Disconnect the plug re- ceptacle of the engine from the plug of the AVR.

Be careful not to	Pliers
damage the fuel
pipe.

!

I 1

;

I

Pipe

Clamp

Strainer

FI& 93-6

-33-

Image 37

Subaru Robin Power Products R1200 service manual Part to Sequencej remOve, Description Precautions, Be careful not to

Contents

Rozh -J &ii Foreword Contents Assembly Items Specifications AC Output Power Factor Rated 800 W Frequency 50 Hz Voltage 110 Output Max Output Max Under no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC Output Features CHOKE-RUN-STOP Component Identification Function of Each Component L-5 Main Bearing Cover 4CONNECTING ROD and PistonCrankshaft Camshaft Carburetor AIR Cleaner Description of Main Operations ‘CC Voltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each Component One section, replace with Assy 83 AVR Windings, or peripheral temperature Resistance Cleaning of Slip RingValue El 10.7J-z Exciting coil At rated rpm Disassembly and Assembly Driver Precautions Tools Precautions Nection Description I2 Remove the front cover SequenceI Part to remove j IFront cover DescriptionBy unscrewing three M5 x 8 screws Part to Sequencej remOve Description PrecautionsBe careful not to Damage the fuel Pipe Lpanner Part to Sequence, removeSpanner @ Driver Remove the connector Assembling, be Remove $Ez End cover Description PrecautionsThat 1wiring Part to See Fig. g-3-10 RemOve ’Rear ‘bracket Description Pull away the stator cover SequenceI Rpearfito~~ Description’ plastic hammer Siw‘ Part to / Sequencej remove ’ JFront Ibracket Description Necessary Precautions13 m/m box Spanner RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housing Necessary Precautions . tools @ Driver One M6 x 12 bolt Precautions Bolt has only to be loosenedBrace nuts 112m/m box ’spanner 10 m/m box jspanner ’Governor Remove the governor lever j Lever Remove the starting pully 26 i &cocci*nIgnition coil from Crank case by taking Notch Spanner 1spring retainer’s Pull out the intake valve and the exhaust valveFront and hook ’ the minus driver Retainer Camshaft Description ISequenceI Part toCrankcase Tappets to distin Guish them from one Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will break Assembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pin Tappets and Camshaft Connecting ROD Intake Valve and Exhaust Valve =53 WV&e h valve guide clearance Breather Plate and Tappet Cover Cylinder Head Tappet Adjustment Ignition COIL, Exciting COIL, Flywheel and Starting Pulley Ignition PlugGovernor Lever Speed Control Muffler and Muffler Cover Nut 1’7 Recoil Startor Head Cover and Blower Housing Front Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe Connection Connection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For Adjustment Uel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring Diagram Maintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095