Manuals / Sun Microsystems / Computer Equipment / Server

Sun Microsystems 816-7727-10 manual Restore the Cabinet, What Next

Models: 816-7727-10

1 62

Download 62 pages 31.5 Kb

Page 42

Restore the Cabinet

Restore the Cabinet

See the instructions provided with your cabinet to complete these steps.

1.Replace the side panels, if applicable.

2.Replace the front and back doors, if applicable.

What Next

The next tasks are to set up a system console device, power on the server, and install the Solaris operating environment. See Chapter 3.

34 Sun Fire V440 Server Installation Guide • July 2003

Image 42

Sun Microsystems 816-7727-10 manual Restore the Cabinet, What Next, Replace the side panels, if applicable

Contents

Sun Fire V440 Server Installation Guide Sun Microsystems, Inc 4150 Network Circle Santa Clara, CA 95054 U.S.AJuly 2003, Revision A Please Recycle Installing a Sun Fire V440 Server Into a 4-Post Cabinet ContentsPreparing for Installation Preface3. Setup and Power -On Procedures iv Sun Fire V440 Server Installation Guide JulyA. Background and Reference Preface How This Book Is OrganizedUsing UNIX Commands Typographic ConventionsSolaris Handbook for Sun Peripherals System Prompts Related DocumentationContacting Sun Technical Support Accessing Sun DocumentationSun Fire V440 Server Installation Guide, part number Sun Welcomes Your CommentsPreparing for Installation About the Parts Shipped to YouVerify that you have received all the parts of your system Verify All Parts2 Sun Fire V440 Server Installation Guide July Inner glidesSun Fire V440 Server Using Online Documentation Plan the InstallationSun Fire V440 Server Safety Information Sun Fire V440 Server Administration GuideWhat Next Install the server into a cabinet, following instructions in Chapter4 Sun Fire V440 Server Installation Guide July Installing a Sun Fire Server Into a 4-Post Cabinet “Connecting the Cords and Cables” on page Checklist of 4-Post Rackmounting Tasks“Install Optional Components” on page “Connect the Power Cords to the Server” on pageInventory for 4-Post Rackmounting Tools Required for Rackmounting Attach the Inner Glides to the Chassis Chapter 2 Installing a Sun Fire V440 Server Into a 4-Post CabinetPrepare the Cabinet Locate the Mounting Holes c. Repeat Step a and Step b for the left front vertical rack rail Install the Slide Assemblies a. Use the holes you marked in Step 6. If the depth of the rack is greater than 27.25 inches 69.21 cm, install a Phillips 8-32 screw and an 8-32 lock nut on each back mounting bracket. Fully tighten the lock nuts Install the Server Into the Cabinet 16 Sun Fire V440 Server Installation Guide JulyChapter 2 Installing a Sun Fire V440 Server Into a 4-Post Cabinet 18 Sun Fire V440 Server Installation Guide July Chapter 2 Installing a Sun Fire V440 Server Into a 4-Post Cabinet What NextInstall the Cable Management Arm Not supplied in kit3. Attach one end of the cable management arm to the inner glide Captive screw Slot Tab Mounting hole Inner glide22 Sun Fire V440 Server Installation Guide July d. Tighten the captive screw on the cable management arm e. Locate the speed pin on the end of the cable management arm Secure the Cords and Cables to the Cable Management Arm Speed pin26 Sun Fire V440 Server Installation Guide July Upper lip Velcro straps Oval cutouts First section Velcro strapsOval cutouts Install Optional Components Install any optional components shipped with your systemConnecting the Cords and Cables PortInformation Connect the Power Cords to the Server 33/66MHz Chapter 2 Installing a Sun Fire V440 Server Into a 4-Post CabinetAC AC 33/66MHzConnect Twisted-Pair Ethernet Cables 1. Choose a network port, using the following table as a guide2. Plug in a Category-5 unshielded twisted-pair cable which is included in your ship kit to the appropriate RJ-45 connector What Next Restore the Cabinet34 Sun Fire V440 Server Installation Guide July 1. Replace the side panels, if applicableSetup and Power-On Procedures Set Up a System Console DeviceAbout Connecting the Server to a Terminal Server 36 Sun Fire V440 Server Installation Guide JulyTABLE 3-1 shows the crossovers that the cable must perform 1. Open a terminal session on the connecting device, and type How to Access the System Console via a Terminal ServerHow to Access the System Console via an Alphanumeric Terminal 1. Turn off power to the alphanumeric terminalHow to Access the System Console via tip Connection 2. Connect the RJ-45 serial cable and RJ45/DB25 adapter Prepare to Configure the Primary Network Interface 4. Determine which name service that the system will use1. Choose a host name for the server and make a note of it Power On the Server How to Power On via the Power Button 9. Press the Power button How to Power On via the poweron Command6. At the ALOM prompt sc, enter the following command sc console 10. Turn the system control keyswitch to the Locked position2. Turn on power to any peripherals and external storage devices 46 Sun Fire V440 Server Installation Guide July Install the Solaris Operating Environment and Additional Software 2. Install the Solaris operating environment on your server1. Locate your Solaris Media Kit 48 Sun Fire V440 Server Installation Guide July What NextBackground and Reference System LEDsThe following table describes the disk drive LEDs The following table describes the power supply LEDsTABLE A-2 Power Supply LEDs TABLE A-1 System Status LEDsSerial Port Connector Serial Port Connector DiagramSerial Port Connector Signals 4-Post Cabinet Requirements TABLE A-4 4-Post Cabinet RequirementsTABLE A-4 4-Post Cabinet Requirements Continued 54 Sun Fire V440 Server Installation Guide July