INSTALLATION Continued

B.If it is a new installation have the gas authorities check meter size and piping to assure that the unit is supplied with necessary amount of gas pressure required to operate the unit..

C.If it is additional or replacement equipment have the gas authorities check pressure to make certain that existing meter and piping will supply fuel to the unit with no more than 0..15 Kpa pressure drop..

D.Make certain new piping and connections have been made in a clean manner and have been purged so that piping compound, chips, etc.. will not clog pilots, valves or burners.. Use pipe joint compound approved for natural and liquefied petroleum gases..

NOTE: Gas pressure should be checked when the unit is installed and all other equipment on the same line is on.. The operating gas pressure must be the same as that specified on the rating plate.. If necessary, pressure adjustment may be made at the pressure regulator supplied with the appliance..

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system where pressures are in excess of 1/2 PSIG (3..45kPa..)

Final Preparation

NOTE: Your new range has a plastic coating to help protective the finish from scratches during shipping.. This protective plastic film should be pealed off prior to starting the range..

TESTING AND ADJUSTMENT

Testing

All fittings and pipe connections must be tested for leaks.. Use approved gas leak detectors, soap solution or equivalent, checking over and around all the fittings and pipe connections.. DO NOT USE A FLAME! Accessibility to all gas lines and fittings require that valve panel(s) lower front panel(s), and/or oven rack(s) be removed.. It may be necessary to remove, or at least raise and securely prop griddle(s), hot top(s), and/or top grate(s).. All parts removed, (including fasteners), should be stored safely for re- installation..

1.Be sure that all valves and thermostats are in the “OFF” position..

2.Turn on the main gas supply valve.. Light all top section pilots..

3.Leak test all valves and fittings as described at the beginning of this section.. Correct any leaks as required and recheck..

4.Light the oven pilot..

5.Set the oven thermostat to maximum.. Leak test all valves and fittings as described at the beginning of this section.. Correct any leaks as required and recheck..

6.Shut off all valves and set thermostat dials to “OFF” or lowest position.. All units are tested and adjusted at the factory, however, burners and pilots should be checked upon installation and adjusted if necessary..

CAUTION: Gas will flow to the top section burners even if top section pilots are not lit.. Gas will not be interrupted.. It is the responsibility of the operator to confirm the proper ignition of each burner as it is turned on.. Should ignition fail to occur 4 seconds after turning a burner on, turn the burner off, wait 5 minutes, and try again..

Page

Part # 4523343 Rev 1 (02/12/08)

Page 7 Page 9
Page 8
Image 8
Sunfire X Series operation manual Testing and Adjustment, Final Preparation
Page 7 Page 9

X Series specifications

The Sunfire X Series is a remarkable line of high-performance audio speakers known for their innovative design and cutting-edge technology. Engineered for audiophiles and music enthusiasts, the X Series delivers an extraordinary audio experience that captivates listeners with its remarkable sound quality and precision.

At the heart of the Sunfire X Series is its patented "Subwoofer" technology, which employs a unique design to produce deep, powerful bass while maintaining clarity across all frequencies. The series incorporates the renowned Sunfire "Compression Technology," allowing for greater output with less distortion. This innovative approach ensures that low-end frequencies are not just felt but experienced in a way that adds depth to every note.

The X Series is equipped with advanced speakers featuring a high-efficiency design that amplifies audio output while minimizing power consumption. This efficiency allows the speakers to deliver rich, full-range sound even in larger spaces, making them perfect for both home theaters and music listening environments. The speakers are also designed to work seamlessly with various audio formats, ensuring compatibility with modern audio systems, including surround sound setups.

One standout feature of the Sunfire X Series is its robust cabinet construction. The use of high-density fiberboard and strategically placed internal bracing minimizes cabinet resonance, reducing unwanted noise and allowing pure sound reproduction. The aesthetically pleasing design is equally functional, allowing for easy integration into any room decor while providing a professional look that complements high-end audio systems.

Additionally, the Sunfire X Series incorporates advanced connectivity options, including wireless capabilities. This allows users to stream high-definition audio directly to the speakers from compatible devices without the clutter of wires. Bluetooth and Wi-Fi connectivity options enhance user convenience, enabling music playback from smartphones, tablets, and computers.

Furthermore, the speakers in the X Series are designed to accommodate various user settings, featuring customizable EQ settings that allow users to tailor the audio output to their personal preferences and room acoustics. This level of adaptability ensures that every listening environment is optimized for the best sound experience.

In summary, the Sunfire X Series exemplifies a commitment to quality and innovation, combining powerful performance with elegant design. Its advanced technologies, including Compression Technology, efficient speaker design, durable construction, and versatile connectivity options, make it a top choice for discerning audio enthusiasts seeking a premium listening experience. Whether for home theater systems or music playback, the Sunfire X Series is designed to impress and deliver immersive soundscapes that bring every note to life.
Top Page Image Contents