Floppy Drive Connector | SUPER MICRO Computer 6015B-8+ specs

SUPERSERVER 6015B-T+/6015B-8+ User’s Manual

5-11 Floppy, IDE, SATA and SCSI Drive Connections

Note the following when connecting the ﬂ oppy and hard disk drive cables:

•The ﬂ oppy disk drive cable has seven twisted wires.

•A red mark on a wire typically designates the location of pin 1.

•A single ﬂ oppy disk drive ribbon cable has 34 wires and two connectors to provide for two ﬂ oppy disk drives. The connector with twisted wires always connects to drive A, and the connector that does not have twisted wires always connects to drive B.

Floppy Drive Connector

The ﬂ oppy connector is located

near the IDE connectors. See the

table below for pin deﬁ nitions.

Floppy Drive Connector

Pin Deﬁnitions (J22)

Pin# Deﬁ nition

1Ground

3Ground

5Key

7Ground

9Ground

11 Ground

13Ground

15Ground

17Ground

19 Ground

21Ground

23Ground

25Ground

27Ground

29Ground

31Ground

33Ground

Pin # Deﬁ nition

2FDHDIN

4Reserved

6FDEDIN

8Index

10 Motor Enable

12 Drive Select B

14Drive Select B

16Motor Enable

18DIR

20 STEP

22Write Data

24Write Gate

26Track 00

28Write Protect

30Read Data

32Side 1 Select

34Diskette

5-24

Image 58

SUPER MICRO Computer 6015B-8+ manual Floppy, IDE, Sata and Scsi Drive Connections, Floppy Drive Connector

Contents

Super Manual Revision 1.0a Release Date July 25 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Sgpio Bios Appendices Superserver 6015B-T+/6015B-8+ Manual Chapter Introduction Overview Memory Serverboard FeaturesProcessors Serial ATA ATI Graphics Controller Other FeaturesPCI Expansion Slots Onboard Controllers/Ports Server Chassis Features Intel 5000P/ESB2 Chipset System Block Diagram Cooling System Europe Contacting Super MicroHeadquarters Asia-Paciﬁc Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the Rack Rails Installing the System into a RackIdentifying the Sections of the Rails Installing the Chassis Rails Identifying the Sections of the Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup DVD-ROM and ﬂoppy disk drives Checking the Drive Bay SetupAccessing the drive bays Check the SATA/SCSI disk drives Supplying power to the system Check the airﬂow Chapter System Interface Control Panel Buttons Control Panel LEDs Sata Drives 6015B-T+ Drive Carrier LEDsScsi Drives 6015B-8+ Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Handling the Serverboard Chapter Advanced Serverboard SetupPrecautions Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1 Dimm Installation See Figure Installing MemoryI/O Ports Installing Dimm into Slot Memory Support Adding PCI Cards PCI card installationPCI slots Serverboard Details Super X7DBR-8+ Layout Connector Description Jumper Description Default SettingX7DBR8+ Quick Reference Connector Deﬁnitions Power Fail LED Overheat/Fan Fail LED OH Universal Serial Bus USB0/1 Ports Reset ButtonPower Button Chassis Intrusion Serial Ports Power Fail HeaderFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/SpeakerExtra Universal Serial Bus Headers Overheat LED Wake-On-LAN Wake-On-Ring Compact Flash Card PWR Connector Alarm Reset JARUnit Identiﬁcation Headers Explanation Jumpers Jumper SettingsCmos Clear Watch Dog Enable/Disable Jlan Enable/Disable3rd Power Supply Fail Detect Enable/Disable Scsi Controller Enable/ Disable 6015B-8+ only VGA Enable/DisableScsi Termination Enable/ Disable 6015B-8+ only Smbus to PCI Enable Disable Compact Flash Master/Slave Select Scsi Activity LED Indicators Onboard IndicatorsJLAN1/JLAN2 LEDs Floppy Drive Connector Floppy, IDE, Sata and Scsi Drive Connections IDE Drive Connectors IDE Drive Connectors Pin Deﬁnitions IDE#1, IDE#2 Sata Ports Ultra320 Scsi Ports 6015B- 8+ only Diffsens Termpwr Superserver 6015B-T+/6015B-8+ User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear Views System Fan Failure Installing a new fanSystem Fans Replacing System Cooling Fans Drive Bay Installation/Removal Removing the Front Bezel Accessing the Drive Bays Removing the Front Bezel SATA/SCSI Drive Installation Mounting a SATA/SCSI drive in a drive carrier Installing/removing hot-swap SATA/SCSI drives DVD-ROM and Floppy Drive Installation Removing/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supply Removing/Replacing the Power Supply Starting the Setup Utility System BiosHow To Change the Conﬁguration Data Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System Date Type Ultra DMA Mode LBA Mode ControlTransfer Mode Multi-Sector Transfers Serial ATA Sata RAID Enable Native Mode OperationAuto Sata Controller Mode Parallel ATA System Memory Advanced SetupExtended Memory QuietBoot Mode Boot FeaturesQuickBoot Mode Post Errors Cache Base 0-512K Memory Cache Cache System Bios AreaCache Video Bios Area Cache Base 512K-640K Discrete Mtrr Allocation PCI Parity Error ForwardingReset Conﬁguration Data PCI Conﬁguration Large Disk Access Mode Enable MasterLatency Timer Serr Signal Condition Clock Spectrum Feature Memory Branch ModeCrystal Beach Features Enabling Multi-Media Timer Advanced Processor Options CPU Speed Serial Port a Device ConﬁgurationKBC Clock Input Base I/O Address Mode InterruptSerial Port B Floppy Disk Controller Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Baud Rate Console RedirectionCOM Port Address Console Type Voltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control Modes CPU Temperature Threshold See note on Hardware Monitor Logic See note on Clear System Event Logging Bios Post Watch DogSystem Event Logging Existing Event Log Number System Event Log/System Event Log List Mode OS Boot Watch DogTimer for Loading OS Minutes Time Out Option Realtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Invalid System Conﬁguration Data PS/2 Mouse Boot Summary ScreenFixed Disk n Device IRQ conﬂict System Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowed Superserver 6015B-T+/6015B-8+ User’s Manual Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Superserver 6015B-T+/6015B-8+ User’s Manual Important Notes to the User Software InstallationIntroduction to Serial ATA and Parallel ATA Serial ATA Sata Intel HostRAID Conﬁgurations Intel Matrix Storage Using the Intel ESB2 Sata RAID Utility Program Creating, Deleting and Resetting RAID Volumes Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility New Operating System-Windows XP/2000/2003 Installation Appendix D System Speciﬁcations Motherboard WeightPower Supply Chassis Regulatory Compliance