Teledyne 465M 4.2.

P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 16

Figure 4-1: M465M Mounting Hole Locations and Dimensions

4.2. Mechanical Installation (19” Rack Version)

The Rack Mount version of the M465M was designed to be operated as a bench-top

monitor or to be mounted in a standard 19” RETMA instrumentation rack. For rack

installations, the four mounting feet should be removed from the bottom of the monitor.

4.2.1. Ventilation Clearance

When installing the M465M be sure to leave sufficient ventilation clearance.

Table 4-2: M465M Ventilation Clearances, Rack Mount Version

Area Minimum required clearance

Back of the monitor 3 inches

Sides of the monitor 1 inch

Above and below the monitor 1/2 inch

Contents

Main INSTRUCTION MANUAL MODEL 465M OZONE MONITOR Page SAFETY MESSAGES CONSIGNES DE SCURIT WARRANTY Page TABLE OF CONTENTS Page FIGURES TABLES 1. INTRODUCTION 1.1. Page 2. SPECIFICATIONS AND AGENCY APPROVALS 2.1. 2.2. 2.2.1. Safety 2.2.2. EMC 2.2.3. Other Type Certifications 3. PRINCIPLE OF OPERATION C Page 4. GETTING STARTED 4.1. Enclosure) 4.1.1. Ventilation Clearance 4.2. 4.2.1. Ventilation Clearance 4.3. NEMA 4X Enclosures) CAUTION 4.4. 4.4.1. Ozone Inlet Connection 4.4.2. Exhaust Connection Page 4.5. 4.5.3. Status Outputs 4.5.4. Hi-Current Relay Outputs 4.5.5. Digital Serial Interfaces 4.5.5.2. RS485 Connection 4.5.5.1. RS232 Connection 4.5.5.3. Ethernet Connection Page Page 6. OPTIONAL HARDWARE AND SOFTWARE 6.1. 6.2. Page 7. OPERATION 7.1. 7.1.1. Ozone Concentration Display 7.1.2. Menu Navigation Keypad 7.1.3. Concentration Alarm Status/Reset 7.1.4. Status LEDs 7.2. 7.2.1. Menu Navigation Basics 7.2.2. Editing Numeric Values Page Page 7.2.3. DIAG Menu 7.2.3.1. Analog Step-Test 7.2.3.2. Signal I/O 7.2.3.3. Memory Reset 7.2.3.4. Zero Calibration 7.2.3.5. Span Calibration 7.2.4. VIEW Menu 7.2.5. SETUP-VARS Menu 7.2.6. SETUP-ALARM Menu 7.2.7. CONFIG Menu Page 8. DIGITAL COMMUNICATIONS 8.1. 8.2. Configuration Page 8.3. 8.4. 8.5. 8.5.1. Hardware Setup for Configuring the Ethernet Module 8.5.2. Verifying Network Hardware Connection 8.5.3. Determining a Dynamically Assigned IP Address (DHCP Mode) 8.5.4. Manually Assigning a Static IP Address Page 8.6. 8.6.1. Notes on MODBUS registers 8.6.2. Real-Time Concentration and Status Registers (Read Only) 8.6.3. Instrument Setup and Configuration Registers (Read / Write) 9. MAINTENANCE 9.1. 9.2. Page 9.3. Page 9.4. 9.5. 9.6. 9.7. 9.8. P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 59 Q1 JP4 + 9.9. 9.10. 9.10.1. Boot Loader Hardware Setup 9.10.2. Boot Loader Software Setup 9.10.2.1. Upload Firmware 9.10.2.2. Verify Firmware Page 10. TROUBLESHOOTING 10.1. 10.1.1. Pneumatic Diagram 10.1.2. Interconnect Diagram P/N 06160D DCN6409 Teledyne API Model 465M O3 Monitor Instruction Manual - Page 65 N/C RACK-MOUNT VERSION ONLY Figure 10-3: Interconnect Diagram 10.2. LEDs or Status Outputs 10.2.1. Sensor OK 10.2.2. Invalid Reading 10.2.3. Check Lamp 10.2.4. Pneumatic Error 10.2.4.1. Pressure Too High 10.2.4.2. Pressure Too Low 11. CALIBRATION 11.1. Page 12. TECHNICAL ASSISTANCE Page 13. M465M SPARE PARTS 13.1. 13.2.