Preparation 1 Turning Power on, Turning power on | Toshiba DP-1810

Preparation 1 - Turning Power ON

Turning power ON

1 Press the power switch to “ ” (ON) side.

The equipment starts warming itself up. The warm-up time takes approx. 25 seconds. When the warm-up has finished, the [START] lamp is lit to show that the equipment is ready for copying.

If you press the [START] button with an original placed while the warm-up is still continu- ing, copying automatically starts after it has finished. This is called auto job start. When the job is reserved, the [START] lamp blinks to show you the current status.

However, this function cannot be accessed while “0” is blinking on the LED display (approx. 15 seconds).

2 Key in the access code if the equipment is managed under the access code function.

Key in the 3-digit access code, and then press the [START] button. Then the equipment is ready for copying.

yIf the access code function is enabled, press the [FUNCTION CLEAR] button after any operation has been finished to prevent unauthorized use of the equipment.

yFor the details of the access code setting, ask your service technician.

Turning power OFF

Press the power switch to “ ” (OFF) side.

Preparation 1 - Turning Power ON 27

Image 29

Toshiba DP-1810 Preparation 1 Turning Power on, Turning power on, Turning power OFF, Press the power switch to on side

Contents

Operators Manual for Copying Functions Page Preface Preface FCC Notice Before Reading This Manual How to read this manual Symbols in this manual Trademarks Description of original/paper direction Contents Switching Operation Sound On/Off Adjusting Density LevelChanging of the Enabled Energy Saving Mode When Message Lamp is Lit/Blinking 105 Daily Inspection Cleaning charger Cleaning transfer charger Contents Recommended toner cartridges Toshiba Quality Is Second to NoneCartridge detecting function Toner remaining check function General Supplies / PartsToner When installing or moving General Precautions 31.5 Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection First-aid measures Poration Disclaimer Notice Low power mode Energy saving featuresSleep mode / Super sleep mode Environmental Information Preparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Front / Right side Description of Each ComponentPlaten Cover optional, KA-1650PC Automatic Document Feeder optional, MR-2020 Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheet Configuration of options Control panel Density adjustment buttons/lamps Original mode button/lampsOriginal setting lamp Interrupt button/lamp APS/AMS selecting button/lamps Copy button/lampsOriginal button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF Press the power switch to on side Types of energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Canceling conditions for energy saving mode Super sleep mode Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Paper types not acceptable Recommended paperStoring paper Media type Product name Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size LD, LT, LT-R, LG, ST-R Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Press the Start button Making Copies Using Bypass TrayPlacing Originals Placing Originals Setting position Type of origiAcceptable originals Maximum number of originals scanned in one go Placing originals on the original glass Placing booklet-type originals such as books or catalogs Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weight Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Check if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as required When the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Bypass copying Paper size has been registered Placed on the bypass tray is lit Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APS Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming in button until Zooming In/Out Copy Image Press the Sort button Copying in Same Page Order as Originals Sort Copying Button Sort buttonOriginal is scanned Repeat this until all originals have been scanned Copying Both Sides of Card into 1 Page ID Card Page Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode Dark Settings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Press and hold Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Press Button to switch the enabled mode Changing of the Enabled Energy Saving ModeAuto sleep time Zooming in button to change When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Cover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lamp Recommended toner cartridges Paper jam lamp Service call lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams Paper jams within Automatic Document Feeder optional Lower When releasing jammed paperOpen the Automatic Document Feeder Do not tear jammed paper Paper Jams Raise the lever and open the upper cover Paper jams within Automatic Document Feeder optional Upper Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Paper Jams Paper jams within Paper Feed Unit optional Never attempt to incinerate toner cartridges Replacing Toner CartridgeOpen the front cover Hold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Original/Copy paper-related items Toner-related items Image trouble Before Calling Service Technician Page Daily Inspection Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Page Continuous copying speed 103 Packing list STUDIO181 Specifications 102Specifications of Options 104 OPC STUDIO181 Specifications Paper size Feeder Continuous Copying speed Continuous copying speedPacking list Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Index 102 Page Multifunctional Digital Systems